Avaya Secure Router 2330 Скачать руководство пользователя страница 31

Страница: 31 / 126

Figure 11: 4-port FXS Small Module

The following table lists the connectors and cable to use with the 2- and 4-port FXS Small
Modules.

Table 10: Cable and connectors

Port

Connector

Recommended

cable type

Minimum cable

length

Loop length

FXS

RJ11

24 AWG
Category 5
twisted pair
cable

N/A

5500 ft (1676.4
m)

Important:

Ensure you use straight cables with FXS modules. TIP must connect to TIP and RING must
connect to RING. FXS ground start does not work if polarity is reversed.

The following table describes the LED states for the 2- and 4-port FXS Small Modules.

Table 11: Module LEDs

LED

Description

LINK/STAT 1

Status of interface 1:

• Red: The port is not configured

• Green: A call is in progress

• Yellow: The port is configured and ready to accept calls

LINK/STAT 2

Status of interface 2:

• Red: The port is not configured

• Green: A call is in progress

• Yellow: The port is configured and ready to accept calls

LINK/STAT 3
(applicable to 4-
port module only)

Status of interface 3:

• Red: The port is not configured

• Green: A call is in progress

• Yellow: The port is configured and ready to accept calls

Interface modules for the Secure Router 2330/4134

Installation — Hardware Components

August 2013 31

Содержание Secure Router 2330































































































































Результаты поиска

Содержание Secure Router 2330

Отзывы:

Бренды по названию

Популярные бренды

Avaya Secure Router 2330, Установка оборудования

Результаты поиска

Содержание Secure Router 2330

Отзывы:

Бренды по названию

Популярные бренды