Avaya Secure Router 2330 Скачать руководство пользователя страница 87

Страница: 87 / 126

3. Remove the three screws securing the right-hand side bracket to the chassis and

the top cover.

4. Remove the three screws securing the right-hand side of the top cover to the

chassis.

5. Slowly slide the top cover back to take it off of the Secure Router 2330.

Installing or removing the internal SCIM module on the
Secure Router 2330

Use the instructions in this section to install, remove, or replace the internal SCIM module on

the Secure Router 2330. This internal module is not hot swappable.

If you ordered the SCIM module with your Secure Router 2330, the Secure Router ships with

the SCIM module installed. The estimated average time to install the internal SCIM module is

fifteen minutes.

Caution:

Do not open the Secure Router 2330 top cover while the unit is powered.

Installing the internal SCIM module

Use the procedure in this section to install an internal SCIM module. If you are replacing a

SCIM module, also see

Removing the internal SCIM module

on page 88.

Prerequisites

• Ensure you have a SCIM module ready to install before opening the chassis top cover.
• Ensure you have a Phillips #1 screwdriver.
• Ensure the Secure Router 2330 is powered off.

Procedure steps

1. Remove the Secure Router 2330 top cover. For information, see

Removing the

Secure Router 2330 top cover

on page 86.

2. Locate the internal SCIM module connector slot.
3. Holding the SCIM module by its edges, align the connector with the slot on the Main

Board, pushing down gently, but firmly, to seat the module.

The following figure shows the location for installing the SCIM module.

Installing or removing the internal SCIM module on the Secure Router 2330

Installation — Hardware Components

August 2013 87

Содержание Secure Router 2330































































































































Результаты поиска

Содержание Secure Router 2330

Отзывы:

Бренды по названию

Популярные бренды

Avaya Secure Router 2330, Установка оборудования

Результаты поиска

Содержание Secure Router 2330

Отзывы:

Бренды по названию

Популярные бренды