Avaya Secure Router 2330 Скачать руководство пользователя страница 35

Страница: 35 / 126

Table 15: Module LEDs

LED

Description

STAT

General module status:

• Off: No power available to the module

• Yellow: Out of service, or failed to initiate

• Green: Power on and the module is operational.

LINK/STAT 1–8

Status of each interface (1 through 8):

• Off: Not connected or the interface is out of service.

• Yellow: The interface is in a loopback mode or is running diagnostics

• Green: The link or channel is active and receiving a valid signal

HSSI Medium Module (supported on Secure Router 4134 only)

The 1-port High Speed Serial Interface (HSSI) Medium Module provides one external
multiprotocol HSSI serial WAN port that operates at up to 52.0 Mbps. The HSSI Medium
Module operates in DTE or DCE mode.

The following figure shows the 1-port HSSI Medium Module.

Figure 15: 1-port HSSI Medium Module

Table 16: Cable and connectors

Port

Connector

Recommended

cable type

Minimum cable

length

Maximum cable

length

High-speed
serial

50-pin HSSI

HSSI null
modem cable

None

50 ft (15 m)

Table 17: Module LEDs

LED

Description

LINK/STAT

Status of interface:

Interface modules for the Secure Router 2330/4134

Installation — Hardware Components

August 2013 35

Содержание Secure Router 2330































































































































Результаты поиска

Содержание Secure Router 2330

Отзывы:

Бренды по названию

Популярные бренды

Avaya Secure Router 2330, Установка оборудования

Результаты поиска

Содержание Secure Router 2330

Отзывы:

Бренды по названию

Популярные бренды