Avaya J129 Скачать руководство пользователя

Страница: 71 / 133

Parameter

Default
value

Description

AMPLIFIED_HANDSET

Specifies whether the handset amplification is enabled.

AMPLIFIED_HANDSET_NOMI
NAL_LEVEL_CALL_END

Specifies whether to set the volume level in amplified mode to
nominal when all calls end.

TIMEFORMAT

Specifies whether the time format is the am-pm format or the
24–hour format.

DATE_FORMAT_OPTIONS

Specifies the date display format.

CALL_LOG_ACTIVE

Specifies whether to activate call logging.

DEFAULT_CONTACTS_STOR
E

Specifies the account where all user contacts are added by
default.

ENABLE_PHONE_LOCK

Specifies whether to enable the lock screen password.

SHOW_CALL_APPEARANCE
_NUMBERS

Specifies whether for a user the device displays call
appearance numbers in the call containers.

User profile backup on Personal Profile Manager (PPM)

September 2017

Installing and Administering Avaya J129 IP Phone

Comments on this document? [email protected]

Содержание J129






































































































































Результаты поиска

Содержание J129

Отзывы:

Похожие инструкции для J129

Бренды по названию

Популярные бренды

Avaya J129, Установка и администрирование

Результаты поиска

Содержание J129

Отзывы:

Похожие инструкции для J129

Бренды по названию

Популярные бренды