Avaya J129 Скачать руководство пользователя

Страница: 123 / 133

Parameter name

Default value

Description

list has the following format: host[:port]
[;transport=xxx].

SIPCONFERENCECONTINUE

Specifies if a conference call continues after the
host hangs up.

Value Operation:

• 0: Drop all parties.

• 1: Continue conference

Note:

This parameter is set to 1 in IP Office environment.

SIPDOMAIN

Null

Specifies the domain name to be used during SIP
registration.

The value can contain 0 to 255 characters. The
default value is null.

SIPPORT

5060

Specifies the port the phone opens to receive SIP
signaling messages.

Valid values are 1024 through 65535. The default
value is 5060.

SIPSIGNAL

Specifies the type of transport used for SIP
signaling.

Value Operation:

• 0: UDP

• 1: TCP

• 2: TLS

SLMCAP

Specifies if the SLA Monitor agent is enabled for
packet capture.

Value Operation:

• 0: Disabled (default)

• 1: Enabled and payloads are removed from RTP

packets

• 2: Enabled and payloads are included in RTP

packets

• 3: Controlled from admin menu - Allows you to

enable or disable of RTP packets capture using
local admin procedures.

SLMCTRL

Specifies whether the SLA Monitor agent is
enabled for phone control.

Table continues…

September 2017

Installing and Administering Avaya J129 IP Phone

123

Comments on this document? [email protected]

Содержание J129






































































































































Результаты поиска

Содержание J129

Отзывы:

Похожие инструкции для J129

Бренды по названию

Популярные бренды

Avaya J129, Установка и администрирование

Результаты поиска

Содержание J129

Отзывы:

Похожие инструкции для J129

Бренды по названию

Популярные бренды