Avaya J129 Скачать руководство пользователя

Страница: 107 / 133

Parameter name

Default value

Description

Valid values can contain 0 to 1096 ASCII
characters, including commas. Filenames must
end in

.xml

LLDP_ENABLED

Specifies whether LLDP is enabled.

Value operation:

• 0: Disabled

• 1: Enabled

• 2: Enabled, but only begins transmitting if an

LLDP frame is received.

LOCAL_CALL_PREFIX

DIAL_AS_IS

Sets the prefix for local calls.

Permissible values are the Area Code denoted by
AC, a string of digits, or the default, DIAL_AS_IS.

LOCAL_DIAL_AREA_CODE

Specifies if user must dial area code for calls within
same area code regions.

Value Operations:

• 0: User does not need to dial area code.

• 1: User need to dial area code. When enabled,

the area code parameter (PHNLAC) should also
be configured.

Note:

This parameter is supported when the phone
is failed over.

LOCALLY_ENFORCE_PRIVACY_
HEADER

Specifies whether the phone displays Restricted
instead of CallerId information when a Privacy
header is received in a SIP INVITE message for an
incoming call.

Value Operation:

• 0: Disabled. CallerID information is displayed.

• 1: Enabled. Restricted is displayed.

LOG_CATEGORY

Null

Specifies a list of categories of events to be logged
through syslog and locally.

This parameter must be specified to log events
below the Error level.

The list can contain up to 255 characters.

Category names are separated by commas without
any intervening spaces.

Table continues…

September 2017

Installing and Administering Avaya J129 IP Phone

107

Comments on this document? [email protected]

Содержание J129






































































































































Результаты поиска

Содержание J129

Отзывы:

Похожие инструкции для J129

Бренды по названию

Популярные бренды

Avaya J129, Установка и администрирование

Результаты поиска

Содержание J129

Отзывы:

Похожие инструкции для J129

Бренды по названию

Популярные бренды