Avaya J129 Скачать руководство пользователя страница 5

Страница: 5 / 133

equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for

help.

Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth

for an uncontrolled environment . This equipment should be installed

and operated with minimum distance of 8 in or 20 cm between the

radiator and your body. This transmitter must not be co-located or

operating in conjunction with any other antenna or transmitter.

EU Countries

This device complies with the essential requirements and other

relevant provisions of Directive 1999/5/EC. A copy of the Declaration

may be obtained from http://support.avaya.com or Avaya Inc., 4655

Great America Parkway, Santa Clara, CA 95054–1233 USA.

General Safety Warning

• Use only the Avaya approved Limited Power Source power

supplies specified for this product.

• Ensure that you:

- Do not operate the device near water.

- Do not use the device during a lightning storm.

- Do not report a gas leak while in the vicinity of the leak.

- Limit the power to the device over telecommunications

wiring to 36-57 volt DC or ≤ 1.3 ampere DC.

Trademarks

The trademarks, logos and service marks (“Marks”) displayed in this

site, the Documentation, Hosted Service(s), and product(s) provided

by Avaya are the registered or unregistered Marks of Avaya, its

affiliates, its licensors, its suppliers, or other third parties. Users are

not permitted to use such Marks without prior written consent from

Avaya or such third party which may own the Mark. Nothing

contained in this site, the Documentation, Hosted Service(s) and

product(s) should be construed as granting, by implication, estoppel,

or otherwise, any license or right in and to the Marks without the

express written permission of Avaya or the applicable third party.

Avaya is a registered trademark of Avaya Inc.

All non-Avaya trademarks are the property of their respective owners.

Linux

is the registered trademark of Linus Torvalds in the U.S. and

other countries.

Содержание J129






































































































































Результаты поиска

Содержание J129

Отзывы:

Похожие инструкции для J129

Бренды по названию

Популярные бренды

Avaya J129, Установка и администрирование

Результаты поиска

Содержание J129

Отзывы:

Похожие инструкции для J129

Бренды по названию

Популярные бренды