Avaya J129 Скачать руководство пользователя страница 101 | Manualshive

Страница: 101 / 133

background image

Parameter name

Default value

Description

All emergency numbers will always be supported.

Value Operation:

• 0:

Emergency

softkey is not displayed.

• 1:

Emergency

softkey is displayed without a

confirmation screen.

• 2:

Emergency

softkey is displayed with a

confirmation screen.

Note:

The parameter is set to 0 for IP Office
environment.

ENCRYPT_SRTCP

0

Specifies whether RTCP packets are encrypted or
not. SRTCP is only used if SRTP is enabled using
MEDIAENCRYTIONRTCP. ENCRYPT_SRTCP
parameter controls RTCP encryption for RTCP
packets exchanged between peers. RTCP packets
sent to Voice Monitoring Tools are always sent
unencrypted.

Value Operation:

• 0: SRTCP is disabled.

• 1: SRTCP is enabled.

ENFORCE_SIPS_URI

1

Specifies if a SIPS URI must be used for SRTP.

Value Operation:

• 0: Not enforced

• 1: Enforced

ENHDIALSTAT

1

Specifies if the algorithm defined by the parameter
is used during certain dialing behaviors.

Value Operation:

• 0: Disables algorithm.

• 1: Enables algorithm, but not for contacts.

• 2: Enables algorithm including contacts.

Note:

The parameter is set to 0 for IP Office
environment.

EVENT_NOTIFY_AVAYA_MAX_U
SERS

20

Specifies the maximum number of users to be
included in an event notification message from CM/
AST-II or Avaya Aura

®

Conferencing 6.0 or later.

Valid values are 0 through 1000.

Table continues…

September 2017

Installing and Administering Avaya J129 IP Phone

101

Comments on this document? [email protected]

«
...
99
100
101
102
103
...
»

Содержание J129






































































































































Отзывы:

Нет отзывов

Похожие инструкции для J129

Бренд: Yealink Страницы: 3

Бренд: AU Страницы: 3

Бренд: RATH MICROTECH Страницы: 2

Бренд: DMP Electronics Страницы: 4

Vigilantplant SMARTDAC+ Series

Бренд: YOKOGAWA Страницы: 31

Бренд: UMIDIGI Страницы: 40

Бренд: Teldat Страницы: 165

Бренд: Olympia Страницы: 31

Бренд: WayteQ Страницы: 24

Бренд: Quba Страницы: 64

Бренд: SouthernLINC Страницы: 63

ADR930 Perception

Бренд: Pantech Страницы: 2

Бренд: Doogee Страницы: 40

Бренд: Med-Pat Страницы: 37

SPRINT SPH-L600

Бренд: Samsung Страницы: 159

MyShot II SCH-R460 Series

Бренд: Samsung Страницы: 153

N105 - SGH Cell Phone

Бренд: Samsung Страницы: 130

Бренд: Samsung Страницы: 167

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды