Avaya J129 Скачать руководство пользователя

Страница: 38 / 133

VLAN parameters

The following configuration parameters are used to configure VLAN functionality on the network

switch internal to the phone.

Parameter name

Default value

Description

L2Q

Specifies the VLAN tagging is enabled or
disabled.

Value operation:

• 0: Auto. VLAN tagging is turned on when the

network can support VLAN tagging and
L2QVLAN is non zero.

• 1: On. VLAN tagging is turned on when the

network can support VLAN tagging. The IP
phone sends tagged frames with VLAN =
L2QVLAN, even if L2QVLAN is set to 0.

• 2: Off. VLAN functionality is disabled.

L2Q is configured through:

• Local admin procedure

• A name equal to value pair in DHCPACK

message

• SET command in the

Settings

file

• DHCP option 43

• LLDP

VLANTEST

Specifies the number of seconds that the phone
waits prior to failing back to a different VLAN ID if
no response is received from the DHCP server.

Valid values are 0 through 999.

Value operation:

• 0: The phone continues to attempt a DHCP

REQUEST forever.

VLANTEST is configured through:

•

Settings

file

• A name equal to value pair in DHCPACK

message

VLANSEPMODE

Specifies whether the VLAN separation is enabled
or disabled.

Table continues…

File Server configuration

September 2017

Installing and Administering Avaya J129 IP Phone

Comments on this document? [email protected]

Содержание J129






































































































































Результаты поиска

Содержание J129

Отзывы:

Похожие инструкции для J129

Бренды по названию

Популярные бренды

Avaya J129, Установка и администрирование

Результаты поиска

Содержание J129

Отзывы:

Похожие инструкции для J129

Бренды по названию

Популярные бренды