Avaya J129 Скачать руководство пользователя страница 129

Страница: 129 / 133

Parameter name

Default value

Description

USBPOWER

Controls USB power when power is provided to the
USB interface.

Value operation:

• 0: Turn off USB power regardless of power

source.

• 1: Turn on USB power only if Aux powered.

• 2: Turn on USB power regardless of power

source.

• 3: Turn on USB power if Aux powered or PoE

Class 3 power.

USER_STORE_URI

Specifies the URI path of IP Office for storing user
data.

Note:

If the value of this parameter is set to null,
then the addition, deletion, and modification of

Contacts

is disabled.

USE_QUAD_ZEROES_FOR_HO
LD

Specifies how Hold will be signaled in SDP.

Value Operation:

• 1: “a=directional attributes" will be used

• 0: "c=0.0.0.0" will be used

V
VLANSEPMODE

specifies whether full VLAN separation will be
enabled by the built-in Ethernet switch while the
telephone is tagging frames with a non-zero VLAN
ID. PHY2PRIO is not supported when
VLANSEPMODE is 1.

Value operation:

• 0: Disabled

• 1: Enabled

Note:

This parameter is configured through the
settings file.

VLANTEST

Specifies the number of seconds that the phone
waits prior to failing back to a different VLAN ID if
no response is received from the DHCP server.

Valid values are 0 through 999.

Table continues…

September 2017

Installing and Administering Avaya J129 IP Phone

129

Comments on this document? [email protected]

Содержание J129






































































































































Результаты поиска

Содержание J129

Отзывы:

Похожие инструкции для J129

Бренды по названию

Популярные бренды

Avaya J129, Установка и администрирование

Результаты поиска

Содержание J129

Отзывы:

Похожие инструкции для J129

Бренды по названию

Популярные бренды