Avanti hughes 9200 Скачать руководство пользователя страница 8

Страница: 8 / 81

Avanti Installation Manual 2.0

General

6. CONSUMABLE REQUIREMENTS

Standard Installation Consumables

NOTE:

Cable ties 300mm black / white /clear.

ALL INSTALLATION ENGINEERS SHOULD HAVE

WF100 Cablecon 5.1 compression connector.

ACCESS TO THE COMPLETE INSTALLATION

WF125 Cablecon 6.0 compression connector.

CONSUMABLES LIST OPPOSITE TO ENSURE

Hi-grade multi use barrel F-F connector.

ALL INSTALLATIONS CAN BE COMPLETED ON

Silicon Dielectric grease.

THEIR SCHEDULED DATE.

Silicon based self

–

amalgamating tape.

RX and TX labels.

M8-M10 Rawl-bolts.

WD 40 or equivalent.

WF100 Twin-sat CAI approved foam dielectric.

Installation Consumables.

BRACKETS and FIXINGS.

CABLE.

Standard

60mm

bracket short. 35cm

WF100 Twin-sat CAI approved foam dielectric.

Standard

60mm

bracket long. 55cm

WF125 green direct burial CAI approved.

K+K or A f

rame (Both to have support leg)

Cat5e external grade 100 meter.

20cm / 8in.

Cat5e 2 meter straight patch lead.

46cm / 18in.

4 gang surge protected mains extension.

55cm / 24in.

Twin-sat 7 mm Grommet black / white.

60mm / 2meter or 3meter pole.

7 mm grommet black / white.

bolts for 60mm pole including washers.

10 mm grommet black / white. (WF125)

Universal Clamp.

Cable clips 2 x 7mm masonry grade.

Non penetrating roof mount 60mm.

Cable clips 9mm round masonry grade.

4 x 600mm x 600mm x 50mm flags.

Cable clips 6-7mm round masonry grade.

M10 / 16mm Rawl-bolts.

Pin plugs.

Rapid set postcrete.

Brick plate terracotta.

DRILL BITS.

Brick plate white.

16mm 200mm masonry

External grade clear silicon.

16mm 600mm masonry

Cable ties 300mm black / white /clear.

16mm 1000mm masonry

CONNECTORS.

5.5mm 100mm masonry

WF100 Cablecon 5.1 compression connector.

Grinder cutting disks.

WF125 Cablecon 6.0 compression connector.

Hi-grade multi use barrel F-F connector.

Silicon Dielectric grease.

RJ 45 connectors.

Silicon based self

–

amalgamating tape.

Replacement Cable stripper blades.

RX and TX labels.

Содержание hughes 9200


















































































Результаты поиска

Содержание hughes 9200

Отзывы:

Бренды по названию

Популярные бренды

Avanti hughes 9200, Руководство по установке

Результаты поиска

Содержание hughes 9200

Отзывы:

Бренды по названию

Популярные бренды