Avanti hughes 9200 Скачать руководство пользователя страница 36

Страница: 36 / 81

Site Hardware Preparation

.36

Avanti Installation Manual 2.0

11. PRODELIN SPACEWAY / JUPITER 0.74M ANTENNA ASSEMBLY

The reflector bracket shown in Figure 4 supports the antenna

reflector and enables the reflector to rotate so that it can

be adjusted for proper tilt. The reflector bracket attaches to

antenna at the Az/El mount assembly.

FIGURE 4

Reflector bracket

The antenna reflector shown in Figure 5 focuses the transmitted and

received RF signals. It attaches to the reflector bracket.

FIGURE 5

ANTENNA REFLECTOR

CAUTION

To avoid damage to the antenna reflector, handle it with care. After assembly, do not use the reflector to rotate

the antenna.

11.3 FEED SUPPORT ARM

(Spaceway)

Figure 6 shows the feed support

arm. The feed support arm supports

the radio assembly and feed horn.

It attaches to the reflector bracket.

FIGURE 6

Feed support arm

Содержание hughes 9200


















































































Результаты поиска

Содержание hughes 9200

Отзывы:

Бренды по названию

Популярные бренды

Avanti hughes 9200, Руководство по установке

Результаты поиска

Содержание hughes 9200

Отзывы:

Бренды по названию

Популярные бренды