AVANT 500 Series 2019 Скачать руководство пользователя

Страница: 59 / 64

500 Series

Troubleshooting

Problem

Possible cause

Remedy

Engine does not crank

Main switch off

Turn on the main switch

Battery discharged, battery

voltage too low

Check and charge

Blown fuse

Check fuses. If fuse blows again, find out the cause.

Contact service
Also check the main fuse that is installed in the

battery cables.

Battery cables poorly connected

Check battery cables and posts, clean and retighten

if necessary

Engine cranks but does not

start, or starts and stops

immediately

No fuel or wrong type of fuel

Fill the tank with correct type of fuel.

Engine does not get fuel, clogged

fuel filter or fuel line

Fill the tank with correct type of fuel.

Make sure that the fuel hoses and fuel filter are

clean and have not been frozen. Replace fuel filter,

clean fuel lines.

Cold ambient temperature

Hold ignition key in glow position for longer period.

If glow indicator lamp is lit, allow it to turn off before

starting. Extend starting time up to 5 seconds.
Use correct type of engine oil

Auxiliary hydraulics control lever is

in locking position.

Turn the lever in center (neutral) position.

Battery discharged or damaged.

Jump start with another battery (See page 57), then

charge the battery or replace if damaged

Engine overheats

Clogged radiator

Clean radiator and fan from engine side

Coolant level low

Add coolant

Leaking cooling system

Check coolant pressure reservoir cap for

tightness. Check cooling system and all hoses and

connections.

Hydraulic system overheats

Hydraulic oil level low

Check and refill, see page 54

Clogged oil cooler

Clean cooler and fan

Fan faulty

Check and clean, repair if necessary

Hydraulic oil flow restricted

Make sure auxiliary hydraulics valve is completely

opened when using high flow attachments. Adjust

lever locking plate if necessary.

Hydraulic system overloaded

Use attachment at lower engine rpm, use with

1-pump setting, check attachment for faults.

The loader does not move even

after the parking brake has been

released.

Bad connection on the wiring of the

parking brake switch, blown fuse, or

faulty switch

Check wires, fuse, and switch, repair if necessary.

Contact service.

Low hydraulic charge pressure.

Contact service for pressure check.

Faulty solenoid valve.

Check and replace if possible. Contact service

Troubleshooting

Содержание 500 Series 2019

































































Результаты поиска

Содержание 500 Series 2019

Отзывы:

Похожие инструкции для 500 Series 2019

Бренды по названию

Популярные бренды

AVANT 500 Series 2019, Руководство оператора

Результаты поиска

Содержание 500 Series 2019

Отзывы:

Похожие инструкции для 500 Series 2019

Бренды по названию

Популярные бренды