AVANT 500 Series 2019 Скачать руководство пользователя страница 48

Страница: 48 / 64

500 Series

Maintenance and service

Daily inspections and routine maintenance

Do a routine walk-around check of the loader before each

working shift. Complete the tasks listed below after each

10 working hours according to the hour meter of the loader.

Check at least the following listed points. Do not use the

loader if you notice problems with any of the listed items.

See the following pages for detailed description of each

inspection listed below.

Risk of injuries and unsafe

operation - Do the daily

inspections.

Determine the need for

service before you start the loader. Do

not use the loader if you notice a fault

Risk of burns - Hot parts.

Do the

daily inspections before you start the

engine. If the loader is hot, allow it

to cool before accessing the engine.

Engine and exhaust parts may be

extremely hot after use.

Service, engine

AVANT 523/528/530 is equipped with a Kubota diesel

engine. Service and maintenance instructions for the

engine can be found in the Kubota Operator’s Manual

supplied with the loader.

If there is conflicting information between this manual

and the engine manual, follow the instructions of this

Operator’s Manual.

Before you start the loader

General condition of loader

Cleaning of the loader

Greasing of the loader

Visual inspection of boom and other metal struc-

tures for defects

Check and tightening of bolts, nuts, and fittings

Tire check

Hydraulic oil level

Attachment and its locking

Engine related inspections

Level of engine oil

10 Coolant level

11 Water in fuel

12 Air filter element

13 Battery and electric cables

After you start the loader

Drive control and steering

15 Movements of boom

WARNING

Содержание 500 Series 2019

































































Результаты поиска

Содержание 500 Series 2019

Отзывы:

Похожие инструкции для 500 Series 2019

Бренды по названию

Популярные бренды

AVANT 500 Series 2019, Руководство оператора

Результаты поиска

Содержание 500 Series 2019

Отзывы:

Похожие инструкции для 500 Series 2019

Бренды по названию

Популярные бренды