AVANT 500 Series 2019 Скачать руководство пользователя

Страница: 44 / 64

500 Series

Operating instructions

Cabs

AVANT 500 series can be equipped, as an option, with cab

L, LX or DLX. All cabs are ROPS and FOPS certified.

Cab

Cab DLX

Switches in cab DLX

On CAB DLX some the switches

shown in detail on page 24 are

located on the control panel up

to the right. The panel includes

switches for

• parking brake

• drive speed range selection

switch (530)

• heater fan

• hydraulic attachment coupling

plate

• emergency blinkers

• warning beacon.

Windscreen washer and wiper

Windscreen washer tank and filler

cap on machines with cab LX and

DLX are located outside the cab, in

front of the windscreen on the left.

On machines with cab L the tank is

located behind the front left wheel and

the filler opening is on the footboard.

Defrosting/Demisting

• Turn heater fan to position 4

• Set temperature to warmest possible

• Direct front vents towards the windows. Close other vents.

Do not drive unless basic visibility in all

directions is achieved. Allow the loader

to warm up properly.

ROPS

canopy

Cab L Cab LX Cab DLX

ROPS & FOPS

Certified

Mounts on standard

rops frame

N/A

Windscreen,wiper

and washer, right

side window and

rear window

door and heater

Front lights

Road traffic light kit Option

Option

Work light kit

Option

Panel interior, fab-

ric seat, radio

Front/rear mud-

guards

-/Option -/Option x/Option

x/x

Seat heater

Seat belt

2-point 2-point 3-point

3-point

Air suspension seat

Option

WARNING

Содержание 500 Series 2019

































































Результаты поиска

Содержание 500 Series 2019

Отзывы:

Похожие инструкции для 500 Series 2019

Бренды по названию

Популярные бренды

AVANT 500 Series 2019, Руководство оператора

Результаты поиска

Содержание 500 Series 2019

Отзывы:

Похожие инструкции для 500 Series 2019

Бренды по названию

Популярные бренды