AVANT 500 Series 2019 Скачать руководство пользователя

Страница: 38 / 64

500 Series

Operating instructions

Allow the loader to warm up properly

Hydraulic oil temperature has an effect on the hydrostatic

drive system of the loader. When the ambient temperature

is below 5ºC, make sure the general response to drive

pedals is normal. If the drive feels sluggish, allow the

hydraulic system to warm up by letting the auxiliary

hydraulics pump to run at idle. Drive carefully until the

loader has reached its normal operating temperature.

Risk of decreased braking power

- Make sure hydraulic oil is not

overheated.

When hydraulic oil

gets hot, driving characteristics of

the drive system change. When the

oil is hot and the hydraulic oil cooler

has switched on, stopping distance

of the machine can be longer than

when the machine is cold. If the

loader is used constantly in high

ambient temperatures, hydraulic oil

type and viscosity must be suitable

for these conditions. Contact Avant

service.

In case the braking power of the

hydrostatic drive system has

decreased, engage the parking

brake. The rear wheels may lock

immediately. Parking brake acts

as an emergency brake, and will

also engage in case of loss of oil

pressure. Parking brake is intended

to keep the loader stationary and not

for repeated braking. Engage while

loader moves only when necessary.

Steering of the loader

Steering of the loader is controlled with the steering wheel.

The steering system is hydraulically powered. A practical

way of steering is to steer with your left hand on the knob

of the steering wheel. This way your right hand is free to

operate other functions.

Pay attention to other machines and persons that are

moving in the area. Make sure that there are no persons

in the danger zone of the loader and the attachment. The

danger zone of the loader covers the reach area of the

loader boom, the turning area on the side and in the front

and rear of the loader. Always put down the load when

leaving the machine – the loader is not designed to stay

with the loader boom and load lifted. Learn how to operate

the loader in a safe place.

Always remember – safety first.

Test

all the functions of the loader at an

open and safe place. Make sure that

there are no persons in the operating

area of the machine and the danger

zone of the attachment.

Risk of tipping over - Keep load

close to ground.

When driving,

always keep the loader boom as low as

possible. Risk of tipping over increases

considerably when there is a heavy

load on the loader (a heavy attachment

or a big load in the bucket) and the

boom is up when driving.

Risk of tipping over - Keep load

close to ground.

Never use a high

drive speed when turning. In particular:

when the loader boom is up the stability

of the machine is much weaker when

turning.

Risk of collision and crushing.

Remember that when turning, the

driver´s seat extends beyond the

turning radius of the wheels. Stay

inside the safety frame.

WARNING

DANGER

CAUTION

Содержание 500 Series 2019

































































Результаты поиска

Содержание 500 Series 2019

Отзывы:

Похожие инструкции для 500 Series 2019

Бренды по названию

Популярные бренды

AVANT 500 Series 2019, Руководство оператора

Результаты поиска

Содержание 500 Series 2019

Отзывы:

Похожие инструкции для 500 Series 2019

Бренды по названию

Популярные бренды