AUMA ACVExC 01.2 Series Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 112

background image

5.2.1.

Terminal compartment: open

Figure 20: Open terminal compartment

[1]

Cover (figure shows KP version)

[2]

Screws for cover

[3]

O-ring

[4]

Blanking plugs

[5]

Cable gland (example)

[6]

Flameproof frame

Hazardous voltage!

Risk of electric shock.

→

Disconnect device from the mains before opening.

→

Wait for 30 seconds after power cut-off prior to opening the housing.

1.

Loosen screws [2] and remove cover [1].

Information: The terminal compartment is designed in protection type Ex e
(increased safety). The flameproof interior of the connected device remains
closed when removing the cover [1].

2.

Insert cable glands suitable for connecting cables.

Information: When selecting cable glands observe type of protection (with Ex e
approval) and enclosure protection IP (refer to name plate).
The enclosure protection IP… stated on the name plate is only ensured if
suitable cable glands are used.
Figure 21: Name plate, example with enclosure protection IP68

Information: For shielded cables: Use EMC cable glands.

3.

Seal unused cable entries with approved plugs suitable for the required protec-
tion type.

28

SAVEx 07.2 – SAVEx 16.2 / SARVEx 07.2 – SARVEx 16.2 Control unit: electronic (MWG)

Electrical connection

ACVExC 01.2 Non-Intrusive Modbus RTU

«
...
26
27
28
29
30
...
»

Содержание ACVExC 01.2 Series

















































































































Отзывы:

Нет отзывов

Похожие инструкции для ACVExC 01.2 Series

Бренд: ABB Страницы: 139

Бренд: ABB Страницы: 28

Бренд: ABB Страницы: 59

Бренд: GE Страницы: 8

Бренд: CAME Страницы: 12

Бренд: CAME Страницы: 16

Бренд: Ultrak Страницы: 41

Бренд: Zander Aachen Страницы: 10

Бренд: E-fly Страницы: 16

Бренд: C3 Custom Coolers Страницы: 16

Бренд: FAAC Страницы: 60

Бренд: FAAC Страницы: 12

Бренд: FAAC Страницы: 44

Бренд: FAAC Страницы: 44

Бренд: FAAC Страницы: 8

Бренд: FAAC Страницы: 60

Бренд: FAAC Страницы: 14

Бренд: FAAC Страницы: 68

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды