AUMA ACVExC 01.2 Series Скачать руководство пользователя страница 23

Страница: 23 / 112

4.5.1.

Mounting positions: modify

Flameproof enclosure, danger of explosion!

Risk of death or serious injury.

→

Before opening, ensure that there is no explosive gas and no voltage.

→

Wait for 30 seconds after power cut-off prior to opening the housing.

→

Handle cover and housing parts with care.

→

Joint surfaces must not be damaged or soiled in any way.

→

Do not jam cover during fitting.

Electrostatic discharge ESD!

Risk of damage to electronic components.

→

Earth both operators and devices.

Loosen screws and remove the local controls.

Check whether O-ring is in good condition, correctly insert O-ring.

Turn local controls into new position and re-place.

Cable damage due to twisting or pinching!

Risk of functional failures.

→

Turn local controls by a maximum of 180°.

→

Carefully assemble local controls to avoid pinching the cables.

Fasten screws evenly crosswise.

SAVEx 07.2 – SAVEx 16.2 / SARVEx 07.2 – SARVEx 16.2 Control unit: electronic (MWG)
ACVExC 01.2 Non-Intrusive Modbus RTU

Assembly

Содержание ACVExC 01.2 Series

















































































































Результаты поиска

Содержание ACVExC 01.2 Series

Отзывы:

Похожие инструкции для ACVExC 01.2 Series

Бренды по названию

Популярные бренды

AUMA ACVExC 01.2 Series, Руководство по эксплуатации

Результаты поиска

Содержание ACVExC 01.2 Series

Отзывы:

Похожие инструкции для ACVExC 01.2 Series

Бренды по названию

Популярные бренды