AUMA ACVExC 01.2 Series Скачать руководство пользователя страница 66

Страница: 66 / 112

10. Press

Yes

to accept new end position setting.

➥

Display indicates:

End pos. CLOSED set!

➥

The left LED is illuminated (standard version) and thus indicates that the end

position CLOSED setting is complete.

11. Make selection:

→

Edit →

back to step 9: Set end position CLOSED "once again"

→

Esc →

back to step 4; either set end position OPEN or exit the menu.

Set end position OPEN

CMD0010

12. Re-set end position OPEN:

12.1 For large strokes: Set selector switch in position Local control (LOCAL)

and operate actuator in motor operation via push button

(OPEN) in

direction of the end position.
Information: Stop actuator before reaching end of travel (press STOP
push button to avoid damage.

12.2 Engage manual operation.

12.3 Turn handwheel until valve is open.

12.4 Turn handwheel by approximately half a turn (overrun) in the opposite

direction of end position.

12.5 Set selector switch to position 0 (OFF).

➥

Display indicates:

Set end pos. OPEN? Yes No

13. Press

Yes

to accept new end position setting.

➥

Display indicates:

End pos. OPEN set!

➥

The right LED is illuminated (standard version) and thus indicates that the end

position OPEN setting is complete.

14. Make selection:

→

Edit →

back to step 12: Set end position OPEN "once again"

→

Esc →

back to step 4; either set end position CLOSED or exit the menu.

Information

If an end position cannot be set: Check the type of control unit in actuator.

9.4.

Output speed (internal): set

This setting is only required if an internally specified speed is set as speed source:

●

Sp. source...

Internal 1

Internal 2

Internal 3

Internal 4

●

Sp. source...

2 DigIn: "Internal (1-4)"

If the actuator is controlled via an external speed source, the internal speed values
described here will not have an impact on the operation behaviour.

For further information on setting the speed source refer to Manual (Operation and
Setting):

Customer settings M0041

Speed functions M1699

Speed internal1 M1930
Speed internal2 M1931
Speed internal3 M1932

SAVEx 07.2 – SAVEx 16.2 / SARVEx 07.2 – SARVEx 16.2 Control unit: electronic (MWG)

Commissioning (basic settings)

ACVExC 01.2 Non-Intrusive Modbus RTU

Содержание ACVExC 01.2 Series

















































































































Результаты поиска

Содержание ACVExC 01.2 Series

Отзывы:

Похожие инструкции для ACVExC 01.2 Series

Бренды по названию

Популярные бренды

AUMA ACVExC 01.2 Series, Руководство по эксплуатации

Результаты поиска

Содержание ACVExC 01.2 Series

Отзывы:

Похожие инструкции для ACVExC 01.2 Series

Бренды по названию

Популярные бренды