AUMA ACVExC 01.2 Series Скачать руководство пользователя страница 70

Страница: 70 / 112

Switch on actuator in direction CLOSE and observe direction of rotation at hollow
shaft [3] or stem [5]:

➥

The direction of rotation is correct if the actuator moves in direction CLOSE

and the hollow shaft in clockwise direction, or the stem moves downward.

Figure 78: Hollow shaft/stem movement (for “clockwise closing”)

[1]

Threaded plug

[2]

Seal

[3]

Hollow shaft

[4]

Protective cap for stem protection tube

[5]

Stem

[6]

Stem protection tube

Correctly fit/screw on threaded plug [1] and seal [2] or protective cap for stem
protection tube [4], fasten thread.

9.6.3.

Limit switching: check

Set selector switch to position Local control (LOCAL).

Operate actuator using push buttons OPEN, STOP, CLOSE.

➥

The limit switching is set correctly if (default indication):

the yellow indication light/LED1 is illuminated in end position CLOSED

the green indication light/LED5 is illuminated in end position OPEN

the indication lights go out after travelling into opposite direction.

➥

The limit switching is set incorrectly if:

the actuator comes to a standstill before reaching the end position

one of the red indication lights/LEDs is illuminated (torque fault)

the status indication

S0007

in the display signals a fault.

If the end position setting is incorrect: Reset limit switching.

SAVEx 07.2 – SAVEx 16.2 / SARVEx 07.2 – SARVEx 16.2 Control unit: electronic (MWG)

Commissioning (basic settings)

ACVExC 01.2 Non-Intrusive Modbus RTU

Содержание ACVExC 01.2 Series

















































































































Результаты поиска

Содержание ACVExC 01.2 Series

Отзывы:

Похожие инструкции для ACVExC 01.2 Series

Бренды по названию

Популярные бренды

AUMA ACVExC 01.2 Series, Руководство по эксплуатации

Результаты поиска

Содержание ACVExC 01.2 Series

Отзывы:

Похожие инструкции для ACVExC 01.2 Series

Бренды по названию

Популярные бренды