Version 6.6
661
Mediant 3000
User's Manual
53. Configuration Parameters Reference
53.3 Debugging and Diagnostics Parameters
This subsection describes the device's debugging and diagnostic parameters.
53.3.1 General Parameters
The general debugging and diagnostic parameters are described in the table below.
General Debugging and Diagnostic Parameters
Parameter
Description
EMS: Enable Diagnostics
[EnableDiagnostics]
Determines the method for verifying correct functioning of the different
hardware components on the device. On completion of the check and if
the test fails, the device sends information on the test results of each
hardware component to the Syslog server.
[0]
= (Default) Rapid and Enhanced self-test mode.
[1]
= Detailed self-test mode (full test of DSPs, PCM, Switch, LAN,
PHY and Flash).
[2]
= A quicker version of the Detailed self-test mode (full test of
DSPs, PCM, Switch, LAN, PHY, but partial test of Flash).
Note:
For this parameter to take effect, a device reset is required.
Web: Enable LAN
Watchdog
[EnableLanWatchDog]
Enables the LAN watchdog feature
.
[0]
Disable (default)
[1]
Enable
When LAN watchdog is enabled, the device's overall communication
integrity is checked periodically. If no communication is detected for
about three minutes, the device performs a self test:
If the self-test succeeds, the problem is a logical link down (i.e.,
Ethernet cable disconnected on the switch side) and the Busy Out
mechanism is activated if enabled (i.e., the parameter
EnableBusyOut is set to 1).
If the self-test fails, the device restarts to overcome internal fatal
communication error.
Notes:
For this parameter to take effect, a device reset is required.
Enable LAN watchdog is relevant only if the Ethernet connection is
full duplex.
Web: Delay After Reset
[sec]
[GWAppDelayTime]
Defines the time interval (in seconds) that the device's operation is
delayed after a reset.
The valid range is 0 to 45. The default is 7 seconds.
Note:
This feature helps overcome connection problems caused by
some LAN routers or IP configuration parameters' modifications by a
DHCP server.
[EnableAutoRAITransmi
tBER]
Enables the device to send a remote alarm indication (RAI) when the bit
error rate (BER) is greater than 0.001.
[0]
Disable (default)
[1]
Enable
Содержание Mediant 3000
