ASTRO ATS-9800 Скачать руководство пользователя

Страница: 29 / 36

SECTION 4

TROUBLESHOOTING

SECTION 4 -- TROUBLESHOOTING

Tabbing Problems:

Problem

Possible Cause

Tab Fold Placement Inconsistent

Tabs not threaded correctly. With Peel Bar

down; space

between

tabs should align with red

marks on side-walls of Tab Drive Assembly.

Rollers dirty, glazed or worn.

Media feeding skewed.

Too Much Tab is Applied to Top of

Tabs not threaded correctly.

Media; even when Tab Fold

With Peel Bar down, space

between

tabs should

Adjustment Knob is turned fully

align with red marks on side-walls of Tab Drive

clockwise.

Assembly.

Horizontal Tab Placement Varies or

Media feeding skewed.

Tabs Not Evenly Applied

Media Side Guides loose.

Multiple Tabs Placed on Single Piece

Media Sensor dirty.

of Media

Dark (non-reflective) area on top side of media.

Try flipping media over.

Media Feeds Without Tabbing

Tab function (Tab Button) not turned ON.

Out of Tabs.

Tabs threaded incorrectly. Tabs must face out

as viewed from exit end of unit.

Tabs not peeling off backing.

Separation set too light - No gap between pieces.

Media Sensor dirty/damaged.

Media positioned incorrectly; missing Sensor.

Fuse F2 on Main PCB is blown. Contact your

local dealer for technical support.

Tabs are Dispensed When No Media

Media Sensor and area below Sensor may need

is Feeding Thru Unit

to be cleaned. See Maintenance Section.

Bright light interfering with Media Sensor

function.

Tab Doesn't Seal Tight Against

Leading edge of media is not staying tightly

Leading Edge of Media.

closed when it hits tab.

Poorly folded media.

Tab does not stay attached to Media

Not enough tab wrap around media edge,

consider using a rectangular tab

Some media surfaces are not acceptable for self

adhesive tab stocks.

Leading Edge of Media is Crushed

Tab is too difficult to bend/fold, for the media

by Tab

being used. Try using translucent tabs.

Media is too light (flimsy) for crash tabbing.

Must use heavier media.

Содержание ATS-9800




































Результаты поиска

Содержание ATS-9800

Отзывы:

Похожие инструкции для ATS-9800

Бренды по названию

Популярные бренды

ASTRO ATS-9800, Руководство оператора

Результаты поиска

Содержание ATS-9800

Отзывы:

Похожие инструкции для ATS-9800

Бренды по названию

Популярные бренды