ASTRO ATS-9800 Скачать руководство пользователя страница 30

Страница: 30 / 36

SECTION 4
TROUBLESHOOTING

Media Feeding Problems:

Problem

Possible Cause

Feeding Doubles

Media not properly fanned before loading.

Nested Media.

Reduce the distance between the Separator

Fingers and the Feed Roller.

Separator Fingers worn.

Media Not Feeding

Media not properly fanned before loading.

Side Guides too tight.

Media Not Feeding Consistently

Check/Adjust Rear Paper Support.

(large gap between pieces)

Increase the distance between the Separator

Fingers and the Feed Roller.

Glazed, dirty or worn Feed Rollers.

Media Opening as it Feeds

Too much friction at separation point. Set Sheet

Separators using 1-1/2 times the material

thickness.

This can happen with last few pieces in Hopper,

because there is no weight to keep piece closed.

Media is Skewing

Media Side Guides too loose.

Separators not set evenly.

Separator Fingers or Feed Rollers worn.

Tabber Transport Stops by Itself

Out of Paper Condition. The Tabber Transport

(Feed Button turns OFF by itself)

will automatically stop after 18 seconds if the

Media Sensor does not detect media.

Media positioned incorrectly - missing Media

Sensor. Adjust the side guides so the media will

pass under the Sensor.

Tabber Transport Keeps Running for

Tabber set for in-line operation. Jumper

a few seconds after Feed Button is

removed from J7 position on board. See details

Pressed (OFF)

under In-Line Setup.

General Problems:

Tabber Not Operating
Power LED not illuminated

Tabber not plugged in.

No AC voltage from wall outlet.

Main Power Switch not turned on.

Line Fuse blown. Unplug power cord and

check/replace fuse.

Use properly rated fuse!

Fuse F 1 on Main PCB blown. Contact your

local dealer for technical support.

Not Advancing Tabs

Tab function (Tab Button) not turned ON.

Power LED illuminated

Media Sensor dirty/damaged.

Media positioned incorrectly; missing Sensor.

Fuse F2 on Main PCB is blown. Contact your

local dealer for technical support.

Содержание ATS-9800




































Результаты поиска

Содержание ATS-9800

Отзывы:

Бренды по названию

Популярные бренды

ASTRO ATS-9800, Руководство оператора

Результаты поиска

Содержание ATS-9800

Отзывы:

Бренды по названию

Популярные бренды