ASTRO ATS-9800 Скачать руководство пользователя

Страница: 8 / 36

SECTION 1
GETTING ACQUAINTED

Control Panel

BATCH COUNTER

—

Counts tab cycles. Can be reset to zero by pressing the

small button on the Counter.

NOTE:

The Batch Counter will not count items fed in the "paper feed mode".

It only counts when the unit is in the "tab mode" (tab button illuminated).

SPEED CONTROL

—

Controls the media transport speed of the Tabber.

Clockwise

= faster.

Counterclockwise

= slower.

IMPORTANT:

Changing the transport speed, also changes the tab fold

position. Please adjust the desired transport speed before you adjust for the
desired tab fold position.

FEED BUTTON

—

Used to stop/start Tabber Transport. Illuminates when the

feed system is activated.

POWER LED

—

Illumination indicates that the Tabber's Main Power Switch

is ON, and the unit is receiving power.

TAB BUTTON

—

Used to turn the tab function ON/OFF.

OFF

= Tab Mode Off (

Feeds paper without applying tabs

(

Illuminated

) = Tab Mode Activated

H o w e r

F o o d

Tab

Содержание ATS-9800




































Результаты поиска

Содержание ATS-9800

Отзывы:

Похожие инструкции для ATS-9800

Бренды по названию

Популярные бренды

ASTRO ATS-9800, Руководство оператора

Результаты поиска

Содержание ATS-9800

Отзывы:

Похожие инструкции для ATS-9800

Бренды по названию

Популярные бренды