Manual of Weighing Controller A 810
Page
2
A.S.T. Angewandte SYSTEM-TECHNIK GmbH Dresden
Table of contents
1.
DESCRIPTION ...................................................................................................................................................7
1.1.
F
RONT
P
ANEL
................................................................................................................................................7
1.1.1.
Numeric Display....................................................................................................................................7
1.1.2.
Unit Display ..........................................................................................................................................7
1.1.3.
Status display.........................................................................................................................................7
1.1.4.
Keypad...................................................................................................................................................9
1.1.5.
Rear Panel...........................................................................................................................................10
1.2.
P
ANEL CUT SIZE
...........................................................................................................................................10
2.
CONNECTIONS ...............................................................................................................................................11
2.1.
L
OADCELL
C
ONNECTOR
...............................................................................................................................11
2.2.
PIN-
A
SSIGNMENT OF
C
ONTROL
S
IGNAL
I
NPUT
/
O
UTPUT
C
ONNECTOR
......................................................12
2.3.
C
ONTROL
I
NPUT
S
IGNALS
............................................................................................................................16
2.4.
C
ONTROL
O
UTPUT
S
IGNALS
.........................................................................................................................19
3.
HOW TO GET STARTED...............................................................................................................................21
3.1.
P
ARAMETER SETUP SECTION
........................................................................................................................22
3.1.1.
Submenu “Basic” ................................................................................................................................24
3.1.1.1.
Enable Setup “Set”........................................................................................................................................... 24
3.1.1.2.
Select primary measurement unit “MU” .......................................................................................................... 24
3.1.1.3.
Range of zero setting lower limit “LLZS” ....................................................................................................... 25
3.1.1.4.
Range of zero setting upper limit “ULZS”....................................................................................................... 25
3.1.1.5.
Zero tracking “ZT” .......................................................................................................................................... 25
3.1.1.6.
Zero tracking distance “dZT”.......................................................................................................................... 25
3.1.1.7.
Power-on zero setting “POZS” ....................................................................................................................... 26
3.1.1.8.
Minimum Load “ML”...................................................................................................................................... 26
3.1.1.9.
Upper limit taring range “ULtAR”................................................................................................................... 26
3.1.1.10.
Taring Mode “tAR_M”................................................................................................................................ 26
3.1.1.11.
Stable number “StAN” ............................................................................................................................... 27
3.1.1.12.
Stable range “StAR” ................................................................................................................................... 27
3.1.1.13.
Limit underload “LUNL” ........................................................................................................................... 27
3.1.1.14.
Limit overload “LOVL” ............................................................................................................................. 27
3.1.1.15.
Enable quickstart “EnQS” ........................................................................................................................... 28
3.1.1.16.
Select character of free unit “CM1”............................................................................................................. 28
3.1.1.17.
Select character of free unit “CM2”............................................................................................................. 28
3.1.1.18.
Set to default “dEF”..................................................................................................................................... 29
3.1.1.19.
Clear Setup “CLEAR”................................................................................................................................. 29
3.1.2.
Submenu “Scale division”...................................................................................................................30
3.1.2.1.
Parameter for unit “MU”.................................................................................................................................. 30
3.1.2.1.1.
Divisions “DN” ......................................................................................................................................... 30
3.1.2.1.2.
Verification scale interval “VS”................................................................................................................ 30
3.1.2.1.3.
Fullscale “FS” ........................................................................................................................................... 30
3.1.3.
Submenu “ADC” .................................................................................................................................32
3.1.3.1.
Filter component “FC”..................................................................................................................................... 32
3.1.3.2.
Threshold of filter jump “FT” .......................................................................................................................... 32
3.1.3.3.
ADC sampling rate “SR” ................................................................................................................................. 32
3.1.3.4.
Display Frequency ........................................................................................................................................... 33
3.1.3.5.
Set to default “def”........................................................................................................................................... 33
3.1.4.
Submenu “Calibration” ......................................................................................................................34
3.1.4.1.
Two position practical calibration “2P” ........................................................................................................... 34
3.1.4.1.1.
Zero calibration “ZC” .............................................................................................................................. 34
3.1.4.1.2.
Span calibration with balance “BW”........................................................................................................ 34
3.1.4.2.
Additional calibration points “AddP” .............................................................................................................. 35
3.1.4.3.
Theroretical calibration “TC” .......................................................................................................................... 35
3.1.5.
Submenu “Alibi” .................................................................................................................................36
3.1.5.1.
Alibi memory activate “Act” ........................................................................................................................... 36
3.1.5.2.
Print request to Alibi memory “RQ”................................................................................................................ 36
3.1.5.3.
Minimum Load “MN” ..................................................................................................................................... 36
3.1.5.4.
Alibi confirmation “A-Prt” .............................................................................................................................. 37
3.1.5.5.
Consecutive Number “CN”.............................................................................................................................. 37
3.1.5.6.
Code protection “code”.................................................................................................................................... 37
3.1.5.7.
Delete Alibi memory “dEL” ............................................................................................................................ 37
3.1.5.8.
Set to default ”dEF” ......................................................................................................................................... 38