Artesyn BajaPPC-750 Скачать руководство пользователя страница 69

Страница: 69 / 215

5-4

BajaPPC-750: PMC/PCI Interface

May 2002

The MPC106 registers are accessed through the BajaPPC-750 Configuration
Address and Data registers at FEC0,0000

and FEE0,0000

. To initiate an access,

write the value 0x8000,00

(where

is the MPC106 address of the register you

want to access) to the Configuration Address register at FEC0,0000

. Then the

data for that register may be read from or written to the Configuration Data regis-
ter at FEE0,0000

5.3.1 PCI Command Register

The PCI Command Register at hex offset 04

controls the MPC106 bridge’s abil-

ity to generate and respond to PCI cycles.

Cache Line Size

Latency Timer

Header type

BIST Control (Built-in self test)

Interrupt Line

Interrupt Pin

MIN_GNT (Burst period length)

MAX_GNT (PCI bus access rate)

MPC106 Bus Number Assignment

R/W

Subordinate Bus Number

Target Disconnect Timeout Counter

Res.

Reserved

FBB

SERR

Res.

PER

Res.

MWI

IOS

Register Map 5-1. MPC106 PCI Command

PCI force read lock (see MPC106 manual). 0=disable, 1=enable.

FBB

Fast back-to-back. Hardwired to zero (no fast back-to-back transactions).

SERR

SERR* driver enable. 0=disable, 1=enable.

PER

Parity error response enable. 0=disable, 1=enable.

MWI

Memory-write-invalidate. Hardwired to zero (no MWI command).

Table 5-1. MPC106 PCI Interface Configuration Registers —

Continued

MPC106
Hex Offset

Size in
Bytes

Access
Mode

Register Name

Hex
Default

Содержание BajaPPC-750
























































































































































































































Результаты поиска

Содержание BajaPPC-750

Отзывы:

Похожие инструкции для BajaPPC-750

Бренды по названию

Популярные бренды

Artesyn BajaPPC-750, Руководство пользователя

Результаты поиска

Содержание BajaPPC-750

Отзывы:

Похожие инструкции для BajaPPC-750

Бренды по названию

Популярные бренды