ARM ARM7TDMI Скачать руководство пользователя страница 65 | Manualshive

Страница: 65 / 286

background image

Programmer’s Model

ARM DDI 0210C

Copyright © 2001, 2004 ARM Limited. All rights reserved.

2-19

2.8.5

Interrupt request

The

Interrupt Request

(IRQ) exception is a normal interrupt caused by a LOW level on

the

nIRQ

input. IRQ has a lower priority than FIQ, and is masked on entry to an FIQ

sequence. As with the

nFIQ

input,

nIRQ

passes into the core through a synchronizer.

Irrespective of whether exception entry is from ARM state or Thumb state, an IRQ
handler returns from the interrupt by executing:

SUBS PC,R14_irq,#4

You can disable IRQ at any time, by setting the I bit in the CPSR from a privileged
mode.

2.8.6

Abort

An abort indicates that the current memory access cannot be completed. An abort is
signaled by the external ABORT input. The ARM7TDMI processor checks for the abort
exception at the end of memory access cycles.

The abort mechanism enables the implementation of a demand-paged virtual memory
system. In such a system, the processor is allowed to generate arbitrary addresses. When
the data at an address is unavailable, the

Memory Management Unit

(MMU) signals an

abort.

The abort handler must then:

•

Work out the cause of the abort and make the requested data available.

•

Load the instruction that caused the abort using an

LDR Rn,[R14_abt,#-8]

instruction to determine whether that instruction specifies base register
write-back. If it does, the abort handler must then:

—

determine from the instruction what the offset applied to the base register
by the write-back was

—

apply the opposite offset to the value that will be reloaded into the base
register when the abort handler returns.

This ensures that when the instruction is retried, the base register will have been
restored to the value it had when the instruction was originally executed.

The application program needs no knowledge of the amount of memory available to it,
nor is its state in any way affected by the abort.

There are two types of abort:

•

a Prefetch Abort occurs during an instruction prefetch

•

a Data Abort occurs during a data access.

«
...
63
64
65
66
67
...
»

Содержание ARM7TDMI































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ARM7TDMI

Бренд: National Instruments Страницы: 9

FIELDPOINT FP-1600

Бренд: National Instruments Страницы: 8

Бренд: XESS Страницы: 23

Asynchronous SH7145F

Бренд: Renesas Страницы: 17

Бренд: hilscher Страницы: 154

Бренд: u-blox Страницы: 29

Compact NVR-AS 4000

Бренд: IndigoVision Страницы: 38

Бренд: ebm-papst Страницы: 13

Бренд: NCR Страницы: 15

Бренд: Accusys Страницы: 34

Бренд: audemat Страницы: 93

METERS AND MORE UM2241

Бренд: ST Страницы: 26

AMSTX-CF Series

Бренд: ADLINK Technology Страницы: 73

EK-UNI Holder D5 V3

Бренд: ekwb Страницы: 2

Database Appliance X6-2-HA

Бренд: Oracle Страницы: 473

StudioStation 100

Бренд: Extron electronics Страницы: 4

Бренд: Nedap Страницы: 3

Бренд: Citizen Страницы: 50

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды