ARIS Tensor Zone 2/22 Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 44

background image

38

Tensor

11.

Additional options

11.1

Internal manual override (mechanical)

Operating the manual override with a cordless screwdriver is not permitted because the
transmission can be destroyed due to the high speed!

Turn the drive shaft with an Allen key SW4 at the manual override until the desired position is reached.

11.2

Option hand wheel

Danger of a mechanical stroke.
The hand wheel is only allowed to be used if the system power is off!

1. Turn off operating voltage of the actuator.
2. Press down hand wheel and turn into desired direction.

Adjusted positions remain.

3. If the desired position is reached release the hand wheel (the coupled state releases).

The hand wheel does not rotate in decoupled state.

CAUTION

CAUTION

«
...
36
37
38
39
40
...
»

Содержание Tensor Zone 2/22













































Отзывы:

Нет отзывов

Похожие инструкции для Tensor Zone 2/22

Бренд: ZEHUS Страницы: 28

Бренд: Valfonta Страницы: 12

Бренд: Lawler Страницы: 6

Бренд: Data Aire Страницы: 28

Compact Comfort VAV12

Бренд: SAI HVAC Страницы: 16

Бренд: Saitek Страницы: 15

Бренд: saia-burgess Страницы: 203

Бренд: Sailor Страницы: 1

Бренд: Dickey-John Страницы: 109

by-me Eikon 20526

Бренд: Vimar Страницы: 6

Бренд: hotset Страницы: 2

TITAN-TRACKSIDE-3

Бренд: Remote Control Systems Страницы: 4

Бренд: Unimig Страницы: 4

Бренд: Dantherm Страницы: 36

Бренд: OMEGA AIR Страницы: 12

Бренд: CAME Страницы: 28

EXTA LIFE P-520

Бренд: Zamel Страницы: 10

Бренд: VALPES Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды