ARIS Tensor Zone 2/22 Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 44

background image

22

Tensor

Set value input
Via pin 51/52 the controller receives a set value. When connecting a
potentiometer (1) pin 53 supplies the encoder with the supply voltage.
Via the DIP switches 3 and 4, the controller receives the information for
use of input:
− Set value via poti (1)
− Set value as current (2)
− Set value as voltage (3)

7.2

Confi gure controller connection

To operate a drive control, the DIP switches must be confi gured correct-
ly and the ports on the controller I-ACT (PMR) connected appropriately.

Setting up DIP switches

Component damage by short-circuit.
The DIP switches 1-2 and 3-4 switch to the same outputs. If the DIP switches 1 and 2 or the
DIP switches 3 and 4 are ON during operation, a short circuit can destroy components.
− Do not set DIP 1 and 2 to ON at once
− Do not set DIP 3 and 4 to ON at once

Via DIP 1-2 (1) the actual value output is confi gured. With DIP 3-4 (2) confi gure the set-point input.

Cut off supply voltage, set up DIP switches:

DIP Actual value output

1 ON / 2 OFF

0...10 V

1 OFF / 2 ON

0...20 mA

DIP 1 and DIP 2 to OFF creates an undefi ned condition.

DIP Set value input

3 ON / 4 OFF

0...20 mA

3 OFF / 4 ON

0...10 V

3 OFF / 4 OFF

0...5 V / Poti operation

CAUTION

«
...
20
21
22
23
24
...
»

Содержание Tensor Zone 2/22













































Отзывы:

Нет отзывов

Похожие инструкции для Tensor Zone 2/22

Бренд: ABB Страницы: 2

Бренд: Fairchild Страницы: 2

Бренд: Fairford Страницы: 233

MachXO5-NX Development Kit

Бренд: Lattice Semiconductor Страницы: 2

WisLink LPWAN RAK5146

Бренд: RAKwireless Страницы: 9

CURTIS DC Series

Бренд: NOCO Genius Страницы: 2

Бренд: TimeTec Security Страницы: 2

Бренд: Xylem Страницы: 2

653 - AE Series

Бренд: VAT Страницы: 103

Бренд: Festo Страницы: 62

Lux Intelligent

Бренд: Advanced Страницы: 62

Бренд: intech 21 Страницы: 15

Бренд: Xsens Страницы: 17

ACTIVAL VY51 5H006

Бренд: Azbil Страницы: 20

Бренд: Firmtech Страницы: 19

Бренд: FUTABA Страницы: 6

Commander Site Controller

Бренд: VeriFone Страницы: 34

Бренд: Ultraflex Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды