ARIS Tensor Zone 2/22 Скачать руководство пользователя

Страница: 12 / 44

Tensor

4.5

Initial operation

4.5.1

Electrical connection

Hazardous voltage: Possible stroke!
•

The initial operation must be carried out only by experts!

•

De-energize the actuator before opening.

•

Observe the appropriate regulations during electrical installation and initial
operation.

Connect the actuator as follows (wiring diagram see chapter 4.5.2):

•

Connect the ground wire of the electric supply to the appropriate protective earth terminal.

•

Always refer to the wiring diagram located inside the actuator.

Check prior to initial switch on:

•

Is the actuator undamaged on the outside?

•

Is the mechanical connection correct?

•

Has the electrical connection been made regularly?

•

Check if current type, voltage and frequency match with the motor data (see nameplate on cover and inside the actuator).

•

Insert suitable cable glands for the connection line.

•

Observe the wiring diagram inside the cover.

•

Use separate (shielded) wires for low voltages.

•

Set up limit switches prior to initial operation.

4.5.2

Wiring diagram

Connection 85...265 V AC

Neutral conductor

Phase / Supply 85 ... 265 V AC

Control connection > left-turning

Control connection > right-turning

Connect the ground wire to the housing.

–/+

Connection 24…48 V DC

Control connection > left-turning

Control connection > right-turning

WARNING

Version 24/48 V DC

Содержание Tensor Zone 2/22













































Результаты поиска

Содержание Tensor Zone 2/22

Отзывы:

Похожие инструкции для Tensor Zone 2/22

Бренды по названию

Популярные бренды

ARIS Tensor Zone 2/22, Руководство пользователя

Результаты поиска

Содержание Tensor Zone 2/22

Отзывы:

Похожие инструкции для Tensor Zone 2/22

Бренды по названию

Популярные бренды