ARIS Tensor Zone 2/22 Скачать руководство пользователя

Страница: 37 / 44

Tensor

10.4

Performance data

The maximum surface temperature of the actuators with regard to an ambient temperature of +45 °C is +80 °C.

Protection class

IP65

Motor

•

Supply: 85…265 V AC, 50/60 Hz; 24 V AC/DC

•

Protection: Primary 2A Tr

•

Type: BLDC

•

50/60 Hz±5%, 100% ED

•

Isolation class E acc. to DIN EN 60085

Cable gland

ATEX-certified cable glands acc. to required protection class, e.g.:
WISKA Hoppmann & Muslow GmbH, Type ESKE/1-e 16
EC-Type-examination certificate number: PTB 13 ATEX 1015 X
Ø cable min. 4 mm, Ø cable max. 9 mm

Path cutoff

Digital via magnet sensor

Ambient temperature

-15 °C bis +45 °C

Installation position

Arbitrary

Potentiometer (Option)

Electronic

Travel

28°…100 revolutions

Only fixed installed cables and lines are allowed to be inducted.
The Operator must guarantee an appropriate strain relief.

If an error occurs: Dangerous voltage when the protective conductor is NOT connected.
Possibly electric shock!
•

Connect the protective conductor terminal (s. symbol in actuator enclosure) with
the protective conductor at any time.

•

Do only put the actuator in operation with connected protective conductor!

ADVICE

WARNING

Содержание Tensor Zone 2/22













































Результаты поиска

Содержание Tensor Zone 2/22

Отзывы:

Похожие инструкции для Tensor Zone 2/22

Бренды по названию

Популярные бренды

ARIS Tensor Zone 2/22, Руководство пользователя

Результаты поиска

Содержание Tensor Zone 2/22

Отзывы:

Похожие инструкции для Tensor Zone 2/22

Бренды по названию

Популярные бренды