ARIS Tensor Zone 2/22 Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 44

background image

5

Tensor

•

Working on electric appliances or equipment is only allowed for electrically qualified persons or other instructed persons
under guidance and custody of an electrically qualified person according to the electro-technical regulations.

•

Observe all safety and accident prevention regulations while installing, operating and testing any electrical appliances or
machinery.

•

Prior to all installation or regular work on the actuator make sure to switch off all connected machinery/appliances.

3.

Technical specification

3.1

Functions and application areas (Intended use)

ARIS actuators are exclusively designed for industrial use. ARIS actuators are utilized for operating regulating and shut-off appli-
ances (valves, ball valves, taps, slide valves, dosing pumps, etc.).

ARIS actuators may not be used for:
•

Temperatures below or above the specified data

•

Underground environments

•

Near open fires

•

Under water

3.2

Safe and accurate use

ARIS actuators are factory checked prior to delivery. The final functional testing must be performed within the total system by
qualified technical personnel.

The ARIS company assumes no liability for any direct or indirect damage arising from
•

an insufficient test period of the actuator in the total system,

•

an improper utilization of the actuator,

•

a further utilization after an error was detected.

Perform controls on a regular basis during the operation. Pay particular attention to:
•

intended utilization of the actuator (Chapter 3.1);

•

unusual sounds, severe vibrations or increased temperatures;

•

examine the correct tightening torque and impermeability of fixing screws, cable entries, cable glands and sealing plugs;

•

the condition of the electrical lines.

Should malfunctions arise, you have to stop the actuator and remedy the malfunction.

All persons who do the installation, commissioning and setting must
•

be specially trained and qualified;

•

be mentally and physically capable;

•

observe the operating instructions.

•

Valves, levers and connecting rods are moving during actuator operation.

•

Check for proper function of all emergency equipment on your machinery/system.

•

Check for proper function of the actuator and operated valves after completion of all installation work.

•

Never work with or operate a faulty actuator.

«
...
3
4
5
6
7
...
»

Содержание Tensor Zone 2/22













































Отзывы:

Нет отзывов

Похожие инструкции для Tensor Zone 2/22

Бренд: ABATEC Страницы: 8

Бренд: M&C Страницы: 16

Бренд: Bang & Olufsen Страницы: 9

Бренд: Bang & Olufsen Страницы: 12

Бренд: Hach Страницы: 86

Бренд: TCS Basys Controls Страницы: 2

Бренд: Ebyte Страницы: 35

Бренд: U-Prox Страницы: 3

Бренд: U-Prox Страницы: 25

Бренд: U-Prox Страницы: 2

Бренд: Yealink Страницы: 8

Бренд: SYCLOPE electronic Страницы: 40

Бренд: Timotion Страницы: 10

Бренд: Fancom Страницы: 23

Бренд: Beninca Страницы: 7

Бренд: TFK Страницы: 60

Бренд: Elotech Страницы: 20

Бренд: Intermatic Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды