Argus PiCUS Tree Motion Sensor Online Скачать руководство пользователя страница 42 | Manualshive

Страница: 42 / 83

background image

PiCUS TMSO Manual

42

6.6 Charging the Devices

6.6.1 TMSO.CU

The  battery  of the TMSO.CU  is  charged  via  the  USB  connector. When  connected  to  a  PC,
charging  takes  place  with  a  low  charging  current  according  to  USB2.0.  When  using  the
supplied charger and quick charging cable the charging current is significantly higher.

If  the  TMSO.CU  is  switched  off,  it  is  automatically  switched  on  when  the  USB  cable  is
connected. The

CHARGE LED

then indicates the current charge level:



Fast flashing: charging with high charge current



Slow flashing: charging with low charge current



Permanently lit: charging completed

Charging via USB cable is also possible during use in the field. For safety reasons only a low
charging current is applied. In addition no USB data connection with the connected device is
possible in this operating state.

Furthermore, please note that the battery can only be charged within the correct temperature
window (see technical information under

). If the temperature is too high or too

low the charging process is paused.
This restriction also applies to charging the battery in the field by solar power.

6.6.2 TMSO.IM

The  battery  of  the  TMSO.IM  is  charged  by  wireless
energy transfer.
For this purpose the sensor is placed with its backside
on  one  of  the  TMS.Single  chargers  which  in  turn  is
connected to the supplied charger. It has 6 equivalent
channels  so  that  the  4  single  chargers  and  thus  4
TMSO.IM  and  the  TMSO.CU  can  be  charged
simultaneously.

NOTE!
It is also possible to use any other wireless charging
cradle  that  works  according  to  the  QI  standard.
However  the  devices  were  only  tested  with  the
supplied  TMS.Single  chargers.  Therefore  there  is  no
guarantee for the function in combination with other chargers.

If a switched off sensor is placed on a charging cradle it switches on automatically.
The sensor's status LED and the charger cradle light indicate the current charging status:



Status LED flashes and the lighting of the charging cradle changes evenly between

light and dark: charging process active



Status LED and charger cradle light are lit continuously: charging process completed

The device can be removed from the charger at any time. It then switches off automatically
after a few seconds

The battery can only be charged within the correct temperature window (see technical
information under

). If the temperature is too high or too low the charging

process is paused.

Figure 16 - Charge TMSO.IM

«
...
40
41
42
43
44
...
»

Содержание PiCUS Tree Motion Sensor Online




















































































Отзывы:

Нет отзывов

Похожие инструкции для PiCUS Tree Motion Sensor Online

Бренд: RayTek Страницы: 72

Бренд: Magnetrol Страницы: 40

Бренд: Kawai Страницы: 19

Бренд: Calculated Industries Страницы: 64

NUFLO Scanner 2000 microEFM

Бренд: Cameron Страницы: 8

Бренд: Olympus Страницы: 4

Бренд: Tavool Страницы: 12

Disklavier Mark III Series

Бренд: Yamaha Страницы: 39

Бренд: YOKOGAWA Страницы: 14

Бренд: Kobold Страницы: 44

SoundAdvisor NMS045

Бренд: Larson Davis Страницы: 64

Бренд: Tenma Страницы: 52

miniSERIES Series

Бренд: Valeport Страницы: 25

Seeker 400 Series

Бренд: General Страницы: 24

Бренд: shelyak Страницы: 45

Бренд: THORLABS Страницы: 20

Бренд: OHAUS Страницы: 64

Бренд: Würth Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды