Argus PiCUS Tree Motion Sensor Online Скачать руководство пользователя страница 74 | Manualshive

Страница: 74 / 83

background image

PiCUS TMSO Manual

74

10 Deactivation and Dismantling

This chapter describes the procedure at the end of a project.

10.1 Waking up the Devices

In order for the PTMSO as an entire system to be correctly deactivated and switched off, all
devices must first be woken up.

For the TMSO.IM touch the device with the magnetic pen at the recess in the housing. Hold
the magnetic pen there until the status LED lights up (approx. 1 second) and then remove it
again.
The status LED will light up permanently. The device is still in the same operating state, but
now has its TMSO Radio activated and is ready for communication with the TMSO.CU.

CAUTION!
The TMSO.IM will automatically switch off their TMSO Radio after 15 minutes if they do not
receive any messages from the TMSO.CU!

For the TMSO.CU open the housing cover and touch the

SWITCH

mark on the front panel with

the magnetic pen.
Hold the magnetic pen there until the

CON-LED

lights up (approx. 1 second) and then remove

it again.
As soon as the LED starts flashing, the BLE is active and ready to connect to your mobile
phone. The operating status of the device is not affected by this.

CAUTION!
The TMSO. CU will automatically switch off the BLE after 5 minutes if it does not receive any
messages from the user's mobile phone!

10.2 Deactivation of the System

Start the TMSO.App on your mobile phone and wait for the connection to the TMSO.CU. Then
click on

Central Unit

to open the management window of the central unit and go to the

MGT

tab.
(Reminder:

7.6.1Establish connection to the TMSO.CU

The app automatically queries the current operating status of the system. Since the system is
active, only the

DISABLE

button is enabled. Clicking it starts the deactivation process.

This process is fully automatic, similar to the system test during activation, and is indicated by
a permanently lit

MEAS LED.

During  this  process,  the  deactivation  command  is  sent  to  all  TMSO.IMs  registered  in  the
system  so  that  they  immediately  enter  standby  mode,  indicated  by  a  status  LED  flashing
regularly every second. In addition, the TMSO.CU will connect to the cloud one last time and
add the deactivation timestamp and total run time of this project in the configuration file (OC-
XXXX.cfg).  This  process  can  take  up  to  3  minutes,  depending  on  the  quality  of  the  radio
connection.
The central unit then also switches to standby mode.

Accordingly, the other 3 buttons in the

MGT

tab are now activated in the app.

«
...
72
73
74
75
76
...
»

Содержание PiCUS Tree Motion Sensor Online




















































































Отзывы:

Нет отзывов

Похожие инструкции для PiCUS Tree Motion Sensor Online

Бренд: Eagle Eye Страницы: 3

Бренд: VALTRONICS Страницы: 13

Бренд: JIANGSU Страницы: 8

Бренд: D-tect Systems Страницы: 19

Бренд: Hach Страницы: 38

Бренд: Hach Страницы: 28

Бренд: Hach Страницы: 40

POCKET COLORIMETER II

Бренд: Hach Страницы: 142

Бренд: Hach Страницы: 4

Бренд: Hach Страницы: 308

Бренд: Hach Страницы: 158

Бренд: Hach Страницы: 118

POCKET COLORIMETER II

Бренд: Hach Страницы: 116

Бренд: Hach Страницы: 132

Бренд: Hach Страницы: 8

Бренд: Hach Страницы: 38

Бренд: Hach Страницы: 200

Бренд: Unipulse Страницы: 129

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды