Argus PiCUS Tree Motion Sensor Online Скачать руководство пользователя страница 10

Страница: 10 / 83

PiCUS TMSO Manual

No. Designation

Function

Magnetic switch



Switching on the device



Switch on BLE while the system is active



Reset of the device

USB interface



Data connection with a PC and the TMSO.software



Charging the battery

SIM card holder

SIM card for establishing the LTE connection

CHARGE

Charging LED *

Shows the status of the charging process via USB



Fast flashing: charging with high charge current



Slow flashing: charging with low charge current



Permanently lit: charging completed

MEAS

Measuring LED *



Permanently lit: the TMSO.CU is currently busy processing a task



Flashing every 2 seconds: the PTMSO is currently taking active
measurements

WWAN

LTE LED *

Indication of LTE module activity when connected to the Internet

CON

BLE and WLAN
LED *



Indication of the readiness and activity of BLE for connection to
the user's mobile phone



Indication of WLAN activity when connected to the Internet

TMSO Radio
transmit LED *

Indication of the message transmission to the TMSO.IM

TMSO Radio
Receive LED *

Indication of data reception from the TMSO.IM

Solar cell
connection

Socket to connect the solar cell cable

Position of the LTE
antenna

Mobile connection to the Internet through the LTE module

Position of the BLE
and WLAN antenna

Connection to a local wireless network with Internet access and to the
user's mobile phone

Position of the
TMSO Radio -
antenna jack

Socket for the radio antenna, connection of the TMSO.CU to the
TMSO.IM

Mounting plate
(back of the
housing)

Plate for fastening the device with screws or a lashing strap

Table 2 - TMSO.CU Operation and Display Elements

* If all LEDs are off, the device is either completely switched off or in sleep mode to save
energy.

Содержание PiCUS Tree Motion Sensor Online




















































































Результаты поиска

Содержание PiCUS Tree Motion Sensor Online

Отзывы:

Похожие инструкции для PiCUS Tree Motion Sensor Online

Бренды по названию

Популярные бренды

Argus PiCUS Tree Motion Sensor Online, Руководство по оборудованию

Результаты поиска

Содержание PiCUS Tree Motion Sensor Online

Отзывы:

Похожие инструкции для PiCUS Tree Motion Sensor Online

Бренды по названию

Популярные бренды