Argus PiCUS Tree Motion Sensor Online Скачать руководство пользователя страница 5

Страница: 5 / 83

PiCUS TMSO Manual

2 Abbreviations and agreements

PTMSO

PiCUS Tree Motion Sensor Online
the entire system

TMSO. App

TMSO control software for mobile phones

TMS.Software

Software for Windows PC for transferring and evaluating data acquired
with PiCUS TMS 3 or TMSO

TMSO.IM

TMSO Inclination Sensor

TMSO.CU

TMSO Central Unit

TMSO.Case

TMSO Transport case

TMS.Single charger Wireless charging cradle (contactless energy transfer) for PiCUS TMS 3

or TMSO sensors

TMS.Magnetic pen

Magnetic tool for switching on all PiCUS TMS 3 or TMSO components

BLE

Bluetooth Low Energy

WLAN

Wireless Local Area Network

LTE

Mobile data network, used in this document as a collective term for the
mobile Internet connection over 3G, 3.9G or 4G, depending on
availability

Dropbox

The cloud used by the PTMSO as Internet data storage

TMSO Radio

The specialised radio link for data exchange between the TMSO.IM and
the TMSO.CU

WRM

Wind reaction measurement

Measuring mode of the PTMSO for measuring the tree inclination during
wind events

WRMS

Wind reaction measurement with time slices

Measuring mode of the PTMSO, similar to WRM, but with temporally
even distribution of the acquisition of inclination maxima

CSM

Construction Site Monitoring

Measuring mode of the PTMSO for monitoring the vibrations and ground
movements to which a tree in the immediate vicinity of a construction
site is exposed

Содержание PiCUS Tree Motion Sensor Online




















































































Результаты поиска

Содержание PiCUS Tree Motion Sensor Online

Отзывы:

Похожие инструкции для PiCUS Tree Motion Sensor Online

Бренды по названию

Популярные бренды

Argus PiCUS Tree Motion Sensor Online, Руководство по оборудованию

Результаты поиска

Содержание PiCUS Tree Motion Sensor Online

Отзывы:

Похожие инструкции для PiCUS Tree Motion Sensor Online

Бренды по названию

Популярные бренды