Appear TV DC100 Series Скачать руководство пользователя страница 144

Страница: 144 / 352

APPEAR AS

Confidential

144/352

DTG

Digital Video Group 4.0: AR Conversion and WSS
values are handled according to this
specification.

AFD Manual

The selected AR conversion is used. WSS value:
Source is AFD in user data sections in video
stream (ETSI TS 101 154).

7.2.2.1

Signal Standard (SDI output)

The

MPEG-2/4 SD/HD Decoder

with SDI option contains these parameters for

Signal Standard

Frame Rate

Choose one of the following:

50Hz

–

mostly used in Europe

59.94/60Hz

–

mostly used in USA

If you select 50Hz

–

the

VBI/V ANC/Test lines

section will be available and

Resolution

will display:

•

SD (576i 50Hz)

•

HD 720p 50Hz

•

HD 1080i 50Hz

•

Transparent

If you select 59.94/60Hz,

V. Resolution

will display:

•

HD 720p 59.94Hz

•

HD 720p 60Hz

•

HD 1080i 59.94Hz

•

HD 1080i 60Hz

•

Transparent

Transparent mode is where input = output

V. Resolution

Vertical Resolution of the outgoing stream.

Available for the MPEG-2/4 SD/HD SDI Decoder only.

H. Resolution

Determines the course of action in the event in the incoming video uses
fewer samples than defined in the selected

V. Resolution

format.

For example: if the incoming video uses 544 of the 720 samples in the SD
standard, the video can either be

Centered

(with black bars on both sides to

fill the rest of the samples) or

Scaled

(stretched to fill all samples with

picture).

Horizontal pixels are defined by the standards:

•

SD = 720 (720x480i and 72x576i)

•

1080i = 1920 (1920x1080i)

•

720p = 1280 (1280x720p)

Available for the MPEG-2/4 SD/HD SDI Decoder only.

Содержание DC100 Series

































































































































































































































































































































































Результаты поиска

Содержание DC100 Series

Отзывы:

Похожие инструкции для DC100 Series

Бренды по названию

Популярные бренды

Appear TV DC100 Series, Руководство пользователя

Результаты поиска

Содержание DC100 Series

Отзывы:

Похожие инструкции для DC100 Series

Бренды по названию

Популярные бренды