manualshive.com logo in svg

Ankom TDF, Руководство оператора

Поделиться
Скачать
Ankom TDF Скачать руководство пользователя страница 63

 

Operator’s

 

Manual

 

 

 

 

 

 

 

 

 

Rev

 

A

 

4/30/12

  

   

pg.

 

63

 

 

This diagnostic allows you to test the motor at different speeds (default is 240 RPM) and directions using different amounts of 
fluid. (The type of fluid used is determined by the supply valves that you open.) Before pressing the GO button to start the 
Motor Test, you must first open at least one Supply Valve and one Output Valve. To do that, press the Set Valves button. The 
following screen is displayed. 

 

If you do not open at least one Supply Valve and one Output Valve, the following screen is displayed. 

 

 

Running the Motor Test could leave fluid in some of the lines. After running a 
Motor Test, always run the Clear IDF/SDF Lines diagnostic. 

 

Clear

 

IDF/SDF

 

Lines

 

When you press the Clear IDF/SDF Lines button on the Diagnostics screen, the IDF and SDF lines are cleared of any fluids. 
Before running this diagnostic, place small waste cups at each IDF and SDF station under the nozzles and close the Front Cover 
of the instrument.

 

 

 

 

The

 

valves

 

are

 

not

 

set

 

correctly.

Please

 

set

 

the

 

valves

 

and

 

try

 

again.

 

OK

 

 

 

← 

Set

 

Valves

Amylase

 

Supply

 

(closed)

 

HCl Supply

 

(closed)

 

AMG

 

Supply

 

(closed)

 

Protease

 

Supply

 

(closed)

 

Water Supply

(closed)

 

EtOH95

 

Supply

 

(closed)

 

EtOH78

 

Supply

(closed)

 

Buffer

 

Supply

(closed)

 

IDF

 

Inlet

 

(open)

 

Waste

 

(open)

 

SDF

 

Inlet

 

(open)

 

Output

 

Supply

Содержание TDF















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды