Ankom TDF Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 78

Ankom TDF Скачать руководство пользователя страница 15

Operator’s

Manual

Rev

A

4/30/12

pg.

15

Dietary

Fiber

Analysis

Support

Items

The following support items needed to perform the fiber analysis may be purchased separately:

Item

ANKOM

Part

#

Electronic Balance with four-place readout

TB

Electronic Balance Software

TBS

Heat Sealer for sealing the filter bags

1915 (120V), 1920 (220V)

IDF Filter Bags

DF-I

SDF Filter Bags (used for SDF and TDF procedures)

DF-S

IDF

Flow-Thru

Bags (TDF procedure only)

DF-FT

Solvent Resistant Marker

F08

Rinse Stand

TDF51

Diatomaceous Earth (DE)

XTC

Analysis

Options

using

the

ANKOM

TDF

Dietary

Fiber

Analyzer

The ANKOM

TDF

Dietary Fiber Analyzer can be configured to recover IDF and SDF residue, or to recover TDF residue. To

maximize productivity, this instrument also allows a user to start new procedures (IDF/SDF and TDF) before the previous ones
have completed. The following describes these analyses along with their specific filter bag configurations.

Analysis

Name

Analysis

Description

Upper

Bag

Lower

Bag

IDF/SDF

This analysis is used to determine IDF and SDF residue separately using
two different filter bags. TDF is calculated by adding the IDF and SDF
residue weights corrected for protein and ash content.

IDF SDF

TDF

This analysis is used to determine TDF residue in one filter. In this
analysis, the TDF value consists of the weighed residue corrected for
protein and ash.

IDF

Flow-Thru

(no filter)

SDF

A computer controlled Diagnostics mode is provided through the Control Panel for maintenance and troubleshooting purposes.

«
...
13
14
15
16
17
...
»

Содержание TDF















































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды