manualshive.com logo in svg

Ankom TDF, Руководство оператора

Поделиться
Скачать
Ankom TDF Скачать руководство пользователя страница 12

Operator’s

 

Manual

 

 

 

 

 

 

 

pg.

 

12

 

 

Rev

 

A

 

4/30/12

 

 

 

Waste Fluid Automatic Elimination:

  1 – Waste Tray, 1 – Drain Tube, 1 – Drain Tube elbow connector 

 

    

  

 

 

Enzyme Containers:

  1 – Amylase, 1 – Protease, 1 – AMG 

 

     

     

   

 

Waste Fluid Collectors:

  6 – Filtrate Cups 

 

  

 

 

 

 

 

 

Chemical Containers with lids:

  1 – HCl, 1 – Distilled Water, 1 – Buffer, 1 – 78% EtOH, 1 – 95% EtOH 

 

 

 

   

  

 

 

Chemical Container Holders:

  1 – single container holder, 1 – three container holder 

 

     

3.

 

Connect

 

the

 

Chemical

 

Container

 

Holders

 

to

 

the

 

feet

 

of

 

the

 

instrument.

 

Remove the nuts from the outside of the left and right feet of the instrument. Slide the small single container holder onto
the bolts on the left foot and slide the large three container holder onto the bolts on the right foot. Secure the holders in
place using the nuts. 

Содержание TDF















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды