Amphenol Temposonics R V Analog RH5 Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 64

Amphenol Temposonics R V Analog RH5 Скачать руководство пользователя страница 20

Temposonics

®

R-Series

V

POWERLINK

Operation Manual

I 20 I

Controlling design dimensions are in millimeters and measurements in ( ) are in inches

4.5.1 Installation of RDV with threaded flange

Fix the sensor rod via threaded flange M18×1.5-6g or ¾"-16 UNF-3A.

Hydraulics sealing

There are two ways to seal the flange contact (Fig. 22):

1. Sealing via an O-ring (e.g. 22.4 × 2.65 mm, 25.07 × 2.62 mm) in a

cylinder end cap groove (for threaded flange »C«/»D«)

2. Sealing via an O-ring 16.4 × 2.2 mm (part no. 560 315) in the

flange undercut.

For threaded flange (¾"-16 UNF-3A) »D«/»T«: O-ring 16.4 × 2.2
       mm (0.65 × 0.09 in.) (part no. 560 315)
For threaded flange (M18×1.5-6g) »C«/»M«: O-ring 15.3 × 2.2 mm
       (0.60 × 0.09 in.) (part no. 401 133)
In the case of threaded flange M18×1.5-6g provide a screw hole based on
ISO 6149-1 (Fig. 23). See ISO 6149-1 for further information.

• Note the fastening torques:

RDV-T: 65 Nm
RDV-M: 55 Nm
RDV-C: 65 Nm
RDV-D: 75 Nm

• Seat the flange contact surface completely on the cylinder mounting

surface.

• The cylinder manufacturer determines the pressure-resistant gasket

(copper gasket, O-ring, etc.).

• The position magnet should not grind on the sensor rod.
• The piston rod drilling (≥ Ø 13 mm (≥ Ø 0.51 in.)) depends on the

pressure and piston speed.

• Adhere to the information relating to operating pressure.
• Protect the sensor rod against wear.

Fig. 21: Mounting example of threaded flange »C«/»D«, »M«/»T«

Fig. 22: Possibilities of sealing

NOTICE

S/N: 70019012

14133950141339501413395014133950

S/N: 70019012

14133950141339501413395014133950

S/N: 70019012

Note for installation respectively

for replacement of RDV

The serial numbers (S/N) of cable

and sensor electronics housing must

match, so that the position

measurement is correct.

Serial number

example

NOTICE

Mount the sensor as follows:

1. Mount the flange with sensor rod
2. Mount the sensor electronics housing
3. Connect the cable between flange and the sensor electronics

housing

The steps mentioned above are explained in the following sections.

Installation of a rod-style sensor in a fluid cylinder

The rod-style version has been developed for direct stroke
measurement in a fluid cylinder. Mount the sensor via threaded flange
or a hex nut.
•  Mounted on the face of the piston, the position magnet travels

over the rod without touching it and indicates the exact position
through the rod wall – independent of the hydraulic fluid.

• The pressure resistant sensor rod is installed into a bore in the

piston rod.

Threaded flange »M« / »T«

Threaded flange »C« / »D«

Fastening torques:

RDV-T: 65 Nm

RDV-M: 55 Nm

RDV-C:

65 Nm

RDV-D: 75 Nm

Sealing via O-ring

in cylinder end cap groove

For threaded flange

»C« / »D«

Sealing via O-ring

in the flange undercut

For threaded flange

»D« / »T«

Sealing via O-ring

in the flange undercut

For threaded flange

»C« / »M«

«
...
18
19
20
21
22
...
»

Содержание Temposonics R V Analog RH5

































































Отзывы:

Нет отзывов