Ammann 5932003, Руководство по эксплуатации, Страница: 28 / 174

24 ARX 23-2 T4i, ARX 26-2 T4i
2.1 Main safety precautions
• The driver must comply with technological procedures of
works or instructions of a responsible worker.
• When rolling (traversing) the machine within the workplace,
he must adapt the driving speed to terrain conditions, the
work performed and weather conditions. He must watch
continuously the clearance to avoid collision with any
obstruction.
• If the operator finishes or interrupts operation of the
machine and leaves the machine, he must carry out safety
measures against unauthorized use of the machine and
undesired start up. The operator must remove the key
from the ignition box, lock the cab or dashboard cover and
disconnect the electrical installation using the disconnector.
• When the operation is completed, park the machine at
a suitable parking place (flat, bearing surface) so as not to
endanger stability of the machine; the machine must not
interfere with traffic roads, must not be exposed to falling
objects (rocks), and must be protected against any natural
disaster of another kind (floods, landslides, etc.).
• When parking the machine on roads, the measures
according to road traffic regulations shall be taken. The
machine must be marked properly.
• After finishing the work with the machine, all of the defects,
damages to the machine and any repairs made must be
recorded in the operation logbook. When the operators take
turns, one operator is obliged to report any identified facts
to the other operator.
• The operator must use personal protective equipment –
work clothes, work shoes, protective helmet and protective
goggles.
• He must equip the machine with accessories and equipment
as prescribed.
• He must keep the operator’s stand, foot rests and walkways
clean.
• Keep the machine free of oil contaminants and inflammable
materials.
• If the machine could come into contact with high voltage,
the following principles must be observed:
- try to leave the hazardous zone with the machine;
- do not leave the operator’s stand;
- warn the others to keep off and not touch the machine.
2.1.3 Driver's obligations
• Before starting operation of the machine, the machine
operator is obliged to get familiar with instructions stated
in the documentation supplied together with the machine,
especially with safety precautions, and strictly observe the
instructions. This also applies to personnel assigned to
maintain, adjust and repair the machine. (In case you do not
understand some parts of the manuals, contact the nearest
dealer or the manufacturer.)
• He may drive the machine only if he is fully familiarized with
all functions of the machine and working and operating
elements and knows precisely how to operate the machine.
• The driver is obliged to follow the safety signs located on the
machine and keep them legible.
• Before starting the work, the operator must get familiar with
the workplace environment, i.e. with obstructions, slopes,
utility line system and with necessary types of workplace
protections with respect to the surroundings (noise,
vibration, etc.).
• The operator while working with the machine must be
fastened with the safety belt.
• The safety belt and its brackets must not be damaged.
• When there is a risk to health, human life, property, failures,
during hardware accidents, or there are symptoms of
such risks during operation, the operator must stop his
work and secure the machine against undesired starting,
communicate this to a responsible worker and to a possible
extent notify all the persons exposed to such hazard.
• Before starting operation of the machine, the operator
is obliged to get familiar with the records and operating
deviations found out during the previous work shift.
• Before starting the work, the driver is obliged to inspect
the machine and accessories and to check control elements
and communication and safety equipment for functioning
according to the manual. If he finds a defect that might
endanger the safety of work and is not able to repair it,
then he must not put the machine into operation and must
report the defect to a responsible worker.
• If the operator finds a defect during operation, he must
immediately stop the machine and secure it safely against
undesirable starting.
• During operation the operator must watch the machine run
and record any detected defects into the operation logbook.
• The operator must maintain an operation logbook which is
meant for records of machine acceptances and take-overs
carried out between operators, of defects and repairs done
during operation and keeping files of serious events during
the work shift.
• Before putting the machine into operation, he must check
the brakes and steering for functioning.
• Before the engine is put into operation, the controls must
be in zero positions and no persons are allowed to be in the
danger zone of the machine.
• The driver must always notify the others each time the
machine is put into operation with the help of a sound or
light signal before starting the engine of the machine.
• After a warning alarm, the operator may put the machine into
operation only when all workers have left the endangered
area. During operation of the machine it is necessary to
follow safety instructions and not to carry out any activity
that might endanger the work safety; the operator must be
fully engaged in driving the machine. He must always sit on
the seat while driving the machine.