Ametek BROOKFIELD CT3 Скачать руководство пользователя страница 19

Страница: 19 / 64

AMETEK Brookfield

Page 19

Manual No. M08-372-F1116

The operator sets the trigger value, target deformation (travel distance into the sample) and the test

speed using the Normal menu screen:

TEST: NORMAL
TRIGGER: XXX.X g
DEFORMATION:XXX.X

SPEED: X.XX mm /s

Figure III.6

A normal test performs a single compression cycle when the operator depresses the start button.

Beginning at the position where the trigger load is measured, the probe descends at the programmed

test speed to the target deformation, then returns immediately to home/starting position. Return

travel speed is 4.5mm/s. During the test the running screen is seen as shown below:

TEST: NORMAL
DEFORMATION:XXX.X mm
LOAD: XXXX.X g

Figure III.7

Deformation and Load will remain live displays during the test.
Test results are shown on the reporting screen:

PEAK LOAD: XXXX.X



DEF@PEAK:

XXX.X mm

WORK:

XXXX.X mJ

FINAL LOAD: XXXX.X g

TEMP:

XXX.X F

Figure III.8

Peak load is reported as the maximum measured load during the test.

Deformation at peak is the distance to which the sample was compressed when the peak load occurred.

Work is defined as the energy required to deform a sample. It is calculated by measuring the force

vs. distance to compress or pull apart the sample. Work done is reported in milli-Joules.

Final load is the load at maximum deformation. Often the peak load and final load will be the same

value.

A new feature is the display of adhesive force and adhesiveness in the NORMAL mode. The POST

SPEED of the probe will be the GLOBAL post speed value.

Adhesiveness and Adhesive Force

- These values are measured as the energy and force required

to separate a probe from the sample on the return stroke.

NORMAL mode Final screen

- After the probe has returned to the START position, the display

will show the test results for ADHESIVE FORCE and ADHESION (ADHESIVENESS). Since

only four lines are available on the display, rotate the Select Knob to scroll down to observe the

added parameters as shown in the following figure.

Содержание BROOKFIELD CT3

































































Результаты поиска

Содержание BROOKFIELD CT3

Отзывы:

Похожие инструкции для BROOKFIELD CT3

Бренды по названию

Популярные бренды

Ametek BROOKFIELD CT3, Руководство по эксплуатации

Результаты поиска

Содержание BROOKFIELD CT3

Отзывы:

Похожие инструкции для BROOKFIELD CT3

Бренды по названию

Популярные бренды