Ametek BROOKFIELD CT3 Скачать руководство пользователя страница 40

Страница: 40 / 64

AMETEK Brookfield

Page 40

Manual No. M08-372-F1116

READING:

Peak Positive Force

HARDNESS

Total Negative Area

Adhesiveness

(Indication of Viscosity)

Peak Negative Force

ADHESIVE FORCE

Total Positive Area

Consistency

Fat Free

Low Fat

Modulus

Gradient

(from initial

curve only)

DISCUSSION:

Once the trigger is attained, the force continues to increase until a surface

fracture occurs. The modulus changes at this point to a less steep gradient,

and the force nearly reaches a plateau.

The low-fat sample appears much softer than the fat-free, having increased

flow over the plunger with a visually less grainy and more glossy fluid

appearance. The softer set is characterized by the lower forces and areas

of work measured, as well as the shallower slope. The softer set is also

characterized by the failure to form sample fracture and the absence of peaks

within the curve.

The fat-free sample has a much steeper initial gradient and subsequently higher

values for all measured parameters. Its grainy set structure is characterized

by the large number of peaks attained within the curve, while the increased

viscosity or spoonability is shown within the negative portion of the curve.

PARAMETER

COLLECTION:

Peak force and work (area under load curve) will show on CT3 display when

used as stand alone. With an attached computer and TexturePro CT software

modulus and many other parameters are available.

PARAMETERS:

HARDNESS

Force necessary to attain a given deformation

WORK

Internal strength of bonds within a product

(Total Positive Area)
ADHESIVENESS

Work necessary to overcome attractive forces

(Total Negative Area)

between surface of the food and the materials

with which it comes into contact.

ADHESIVE FORCE

Force required to “pull” probe from sample

(suction).

Содержание BROOKFIELD CT3

































































Результаты поиска

Содержание BROOKFIELD CT3

Отзывы:

Похожие инструкции для BROOKFIELD CT3

Бренды по названию

Популярные бренды

Ametek BROOKFIELD CT3, Руководство по эксплуатации

Результаты поиска

Содержание BROOKFIELD CT3

Отзывы:

Похожие инструкции для BROOKFIELD CT3

Бренды по названию

Популярные бренды