Ametek BROOKFIELD CT3 Скачать руководство пользователя страница 33

Страница: 33 / 64

AMETEK Brookfield

Page 33

Manual No. M08-372-F1116

HOLD TIME Full re-start

After a HOLD TIME test is complete, the operator can do a full restart of the test. Pressing the

STOP button at this time will display the setup screen. This places the CT3 back at the HOLD

TIME setup mode. The probe will return to the HOME position. The various setup parameters can

be modified. Pressing START will begin the full test run complete with pre-positioning.

III.9.3 CYCLE COUNT mode pre-positioning

The pre-positioning screen is displayed after the ATTACH PROBE screen. Move the probe to the

desired START position. The displayed value for deformation will be set to 0.0 mm. All deformation

measurements will then be referenced to the trigger point after the probe makes contact with the

sample.
When the probe is retracted upwards between cycles, it will stop at the START position before

descending for the next cycle. At the end of a CYCLE COUNT test, the probe will return to the

START position. The probe will return to the HOME position only if a full restart of the CYCLE

COUNT test is done.

CYCLE COUNT mode Quick re-start

After a CYCLE COUNT test is complete, pressing the START button will re-run the test starting

at the AUTZERO screen.

CYCLE COUNT Full re-start

After a CYCLE COUNT test is complete, the operator can do a full restart of the test. Pressing the

STOP button at this time will display the setup screen. This places the CT3 back at the CYCLE

COUNT setup mode. The probe will return to the HOME position. The various setup parameters

can be modified. Pressing START will begin the full test run complete with pre-positioning.

III.9.4 BLOOM mode pre-positioning

The pre-positioning screen is displayed after the ATTACH PROBE screen. Move the probe to the

desired START position. The displayed value for deformation will be set to 0.0 mm. All deformation

measurements will then be referenced to the position when the probe makes contact with the sample

and the trigger point is reached.
At the end of a BLOOM test, the probe will return to the START position. The probe will return

to the HOME position only if the full restart of the BLOOM test is done.

BLOOM mode Quick re-start

After a BLOOM test is complete, pressing the START button will re-run the test starting at the

AUTZERO screen.

BLOOM Full re-start

After a BLOOM test is complete, the operator can do a full restart of the test. Pressing the STOP

button at this time will display the setup screen. This places the CT3 back at the BLOOM setup

mode. The probe returns to the HOME position. The various setup parameters can be modified.

Pressing START will begin the full test run complete with pre-positioning.

III.9.5 TPA mode pre-positioning

The pre-positioning screen is displayed after the ATTACH PROBE screen. Move the probe to the

desired START position. The displayed value for deformation will be set to 0.0 mm. All deformation

measurements will then be referenced to the position when the probe makes contact with the sample

and the trigger point is reached.

Содержание BROOKFIELD CT3

































































Результаты поиска

Содержание BROOKFIELD CT3

Отзывы:

Похожие инструкции для BROOKFIELD CT3

Бренды по названию

Популярные бренды

Ametek BROOKFIELD CT3, Руководство по эксплуатации

Результаты поиска

Содержание BROOKFIELD CT3

Отзывы:

Похожие инструкции для BROOKFIELD CT3

Бренды по названию

Популярные бренды