Ametek BROOKFIELD CT3 Скачать руководство пользователя страница 59

Страница: 59 / 64

AMETEK Brookfield

Page 59

Manual No. M08-372-F1116

Appendix B - Troubleshooting

If no power to the instrument:

Check:

• User replaceable fuses: two (2) fuses, 4 amp, 5 x 20 mm, time-lag located behind removable

red color panel just above switch.

• Fuses located within power entry module on the rear of the instrument.

• If the fuses blow continually, serious damage to the instrument could result. Contact repair

services immediately.

Probe won’t attach:

• Check the thread on probe and probe shaft - remove any dirt.

Rotary Base table won’t move:

• Ensure the locking knob is loose.

• Ensure the fine adjust nut is loose.

Rotary Base table will not travel to the lowest position:

• Loosen the fine adjust nut and rotate base table.

• Locate the table in center of T-slot.

Instrument is unsteady:

• Ensure that the bench top is stable.

• Adjust the CT3 feet.

Probe doesn’t move when start is pressed:

• Ensure the emergency stop button is not pressed in (rotate clockwise).

• Ensure the test mode is not in Static Load.

• Ensure the probe is not in contact with sample (or base table).

Display shows “REMOTE OPERATION”

• This will always show when the computer interface cable is connected to the CT3. To use

the CT3 without the computer program, the serial cable must be disconnected.

Содержание BROOKFIELD CT3

































































Результаты поиска

Содержание BROOKFIELD CT3

Отзывы:

Похожие инструкции для BROOKFIELD CT3

Бренды по названию

Популярные бренды

Ametek BROOKFIELD CT3, Руководство по эксплуатации

Результаты поиска

Содержание BROOKFIELD CT3

Отзывы:

Похожие инструкции для BROOKFIELD CT3

Бренды по названию

Популярные бренды