Ametek BROOKFIELD CT3 Скачать руководство пользователя страница 30

Страница: 30 / 64

AMETEK Brookfield

Page 30

Manual No. M08-372-F1116

During the test, the display will show live deformation and load.

TEST: SURIMI

DEFORMATION: XX.XX cm
LOAD:

XXXX.X g

Figure III.33

As soon as the surimi gel ruptures, the result screen will appear.

PEAK LOAD: 465.0 g
DEF@PEAK: 0.81

GEL:

376.65 g *cm

TEMP:

19.8

Figure III.34

The GEL result is the multiplication of Peak Load times Def@Peak in units of g-cm.

If a temperature probe is used with the CT3, the temperature at the time of the test is also shown.

The TEMP line will not be seen in the display if a temperature probe is not used. DO NOT insert

the temperature probe into the surimi sample being tested.

III.8 Global Parameters

The CT3 has a GLOBAL PARAMS screen which allows the pre-setting of: PRE SPEED, POST

SPEED, TEMP. C/F (temperature in C or F), and load measurement unit in “g” (grams) or “N”

(newtons). After Autozero during startup, rotate the Select Knob to reach the GLOBAL PARAMS

screen, then press the Select Knob to access the data entry function.
There are some parameters that affect every test screen. The speed of the probe prior to triggering

is the pretest speed, which is called Pre-Speed on the display screen. This may be set over the

range of 0.1mm/s to 2.0mm/s.

ENTER GLOBAL PARAMS
PRE SPEED:

0.5MM/S

POST SPEED:

10.0MM/S

TEMP. C/F:

19.0C

Figure III.35

The return speed after the target is reached is the post test speed which is called Post Speed on this

screen. It may be set from 0.1mm/s to 10.0mm/s. For some tests, Such as TPA, the post test speed

is irrelevant because it will always be the same as the test speed. The two tests for which this is

the case are TPA and the Cycle test.
Rotate the Select Knob to LOAD UNITS. When the cursor is over the “L” in LOAD, pressing

the Select Knob will reposition the cursor to the “g” or “N” at the far right of the field. Rotating

the knob will alternate between the “g” and “N” (grams and Newtons).

Содержание BROOKFIELD CT3

































































Результаты поиска

Содержание BROOKFIELD CT3

Отзывы:

Похожие инструкции для BROOKFIELD CT3

Бренды по названию

Популярные бренды

Ametek BROOKFIELD CT3, Руководство по эксплуатации

Результаты поиска

Содержание BROOKFIELD CT3

Отзывы:

Похожие инструкции для BROOKFIELD CT3

Бренды по названию

Популярные бренды