Ambit U10C034 Скачать руководство пользователя страница 86 | Manualshive

Страница: 86 / 90

background image

U10C034 Telephony Version v1.4 June 2008

86

pktcNcsEndPntConfigCallAgentUdpPort

Contains the call agent User Datagram Protocol (UDP) receive port that is being used for this
instance of call signaling, i.e. the default port on which the call agent receives NCS signaling from
the gateway. The default port number is

2727

.

pktcNcsEndPntConfigStatus

Contains the Row Status associated with the

pktsNcsEndPntTable.

pktcNcsEndPntConfigCallWaitingMaxRep

Contains the maximum number of repetitions of the call waiting tone that the MTA plays from a
single CMS request. A value of zero

(0)

can be used if the CMS is to control the repetitions of the

call waiting tone.

pktcNcsEndPntConfigCallWaitingDelay

Contains the delay between repetitions of the call waiting tone that the MTA plays from a single
CMS request.

pktcNcsEndPntStatusCallIpAddress

Contains the IP address of the CMS currently being used for this endpoint. This IP address creates
the appropriate security association.

pktcNcsEndPntStatusError

Contains the error status for this interface. The operational state indicates that all operations
necessary to put the line in service have occurred.
The

noSecurityAssociation

status indicates that no security association yet exists for this endpoint.

The disconnected status indicates one of the following:

1. If

pktcMtaDevCmsIpsecCtrl

is disabled, then no security association is involved with this

endpoint; the NCS signaling firmware is in the process of establishing the NCS signaling link
through an RSIP exchange.

2. Otherwise,

pktcMtaDevCmsIpsecCtrl

is enabled, the security association has been established

and the NCS signaling firmware is in the process of establishing the NCS signaling link through an
RSIP exchange.

6.3 LED Verification

Installer can check the LED pattern table to know which state modem kept. If modem has registered
CMTS, PWR, DS, US and Online must be lit. If Tel1 is always flash and Tel2 is always unlit, it
means that MTA can not receive a valid offer from DHCP server. If Tel1 is always unlit and Tel2 is
always flash, it means that MTA can not download configuration file. If Tel1 and Tel2 are flash, it
means that the MTA does not send RSIP to CMS yet (waiting for MWD timeout).

«
...
84
85
86
87
88
...
»

Содержание U10C034



























































































Отзывы:

Нет отзывов

Похожие инструкции для U10C034

WEBR@CER 852 PSTN

Бренд: Topcom Страницы: 38

Бренд: SBC Страницы: 32

Бренд: ADC Страницы: 7

Бренд: Aeotec Страницы: 6

Бренд: Cyta Страницы: 20

Бренд: NAPCO Страницы: 16

Бренд: KaiDeng Страницы: 4

Бренд: Patton electronics Страницы: 28

Harley RS232/USB Modem Moudle AFM-100

Бренд: Abocom Страницы: 1

Бренд: Zoom Страницы: 67

Бренд: NETGEAR Страницы: 26

Бренд: NETGEAR Страницы: 106

Бренд: Gigalink Страницы: 6

Бренд: TRENDnet Страницы: 15

Бренд: XMODUS Страницы: 32

Бренд: Huawei Страницы: 28

Бренд: Kathrein Страницы: 16

Бренд: Zte Страницы: 35

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды