Ambit U10C034 Скачать руководство пользователя страница 69

Страница: 69 / 90

all_sizes

Configures the settings for sweeping all packet sizes from 64-1518.

end_size

Sets or shows the size of the largest ping packet that will be sent.

hs_nowait

Configures the settings for doing high-speed pings, without waiting for the reply.

hs_wait

Configures the settings for doing high-speed pings (infinite), waiting for the reply.

ip_address

Sets or shows the IP address of the device to be pinged.

ip_stack

Sets the IP stack number that the pings should be sent to.

ip_sweep

Pings all IP addresses on the specified subnet.

number_of_pings

Sets or shows the number of pings to be sent.

ping

Begins pinging the specified IP address, using the current settings.

restore_defaults

Restores all of the options to their default values.

show_settings

Displays the current ping settings.

start_size

Sets or shows the size of the first ping packet that will be sent.

stats

Displays the ping statistics summary from the last set of pings.

step_amount

Sets or shows the amount that the packet size will be increased for each packet.

stop

Stops the ping that is currently running.

Содержание U10C034



























































































Результаты поиска

Содержание U10C034

Отзывы:

Похожие инструкции для U10C034

Бренды по названию

Популярные бренды

Ambit U10C034, Руководство пользователя

Результаты поиска

Содержание U10C034

Отзывы:

Похожие инструкции для U10C034

Бренды по названию

Популярные бренды