Ambit U10C034 Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 90

background image

U10C034 Telephony Version v1.4 June 2008

26

If silence suppression will never be enabled by the CMS, all bits may
be set.

Note that this setting only applies if emtaPhsConfiguration is set to
enabled(1). If emtaPhsConfiguration is set to disabled(2), then the value
of this object will be ignored.

‧

ethDA(0),

‧

ethSA(1),

‧

ethEtherType(2),

‧

ipVersionIHL(3),

‧

ipTOS(4),

‧

ipTotalLength(5),

‧

ipIdent(6),

‧

ipFlagsFragOffset(7),

‧

ipTTL(8),

‧

ipProtocol(9),

‧

ipHeaderChecksum(10),

‧

ipSA(11),

‧

ipDA(12),

‧

udpSourcePort(13),

‧

udpDestPort(14),

‧

udpLength(15),

‧

udpChecksum(16)

emtaPhsDownstreamMask

(1.3.6.1.4.1.4413.2.2.2.1.6.1.17.0 BITS)

This object sets the PHS mask for downstream voice DQoS flows using IPv4
addressing. Setting a bit to '1' will cause the CMTS to suppress this
field for downstream voice flows.

The default configuration is the ethEthertype(0), ipVersionIHL(1),
ipIdent(4), ipFlagsFragOffset(5), ipProtocol(7), ipSA(9), ipDA(10), and
udpDestPort(12) bits are set.

If silence suppression will never be enabled by the CMS, ipTotalLength(3)
and udpLength(13) may also be set.

If silence suppression will never be enabled by the CMS and
emtaPhsDownstreamVerification is set to either disabled(2) or auto(3),
all bits may be set.

Note that this setting only applies if emtaPhsConfiguration is set to
enabled(1). If emtaPhsConfiguration is set to disabled(2), then the value

«
...
24
25
26
27
28
...
»

Содержание U10C034



























































































Отзывы:

Нет отзывов

Похожие инструкции для U10C034

Бренд: Allied Data Technologies Страницы: 35

Бренд: TP-Link Страницы: 4

Бренд: THOMSON Страницы: 28

Бренд: TeleWell Страницы: 131

Бренд: Zoom Страницы: 2

Бренд: Ebyte Страницы: 27

PORTAL-STICK PX1

Бренд: SMART Страницы: 12

Бренд: ICPDAS Страницы: 8

CellPipe 20A-USB

Бренд: Lucent Technologies Страницы: 44

WiFi1500CF Plug-In

Бренд: Janus Страницы: 16

Бренд: Janus Remote Communications Страницы: 26

Бренд: H3 System Страницы: 15

Бренд: NETGEAR Страницы: 2

Бренд: Zte Страницы: 7

Бренд: RACOM Страницы: 171

Бренд: Data Connect Страницы: 23

DCM202 - Express Ethernetwork DOCSIS 2.0 Cable...

Бренд: D-Link Страницы: 7

Бренд: Askey Страницы: 51

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды